17mm ball mount socket 3d models

I wanted a simple way to fine-tune a tiny mirror for my laser project, so I came up with this versatile ball-and-socket mount. It comes equipped with adjustable screw holes, but for mine, I'm just relying on sticky-tack. Check out the customizer...

Based on the excellent Ball and Socket by Antscran I made this to stick my camera on my car, you'll find the original here : https://www.thingiverse.com/thing:2069128

Engineer: Design a custom adapter for Leonardo da Vinci's mechanical devices to integrate a ball and socket arm with a modern webcam, enabling innovative angles and perspectives for capturing images and videos.

GoPro owners can harness its full potential by attaching it to a ball socket joint, allowing the camera to move freely when placed on any magnetic surface or alternative stand, designed specifically for GoPros.

22mm bar clamp to garmin 17mm ball mount. ...allowing you to mount an old car sat nav on handlebars or accessory bar.

This is an adapter that converts AMPS holes (4mm holes at 30mm x 38mm spacing) to a 17mm ball mount (iOttie phone mounts, Garmin Nuvi, etc). ...

http://www.thingiverse.com/apps/customizer/run?thing_id=1085548 Instructions Using the Following Options Socket Thickness: 2.5 Millimeters Flange Diameter: 40 Millimeters Screw Head Size: 6.5 Millimeters Neck Length: 10 Millimeters Flange Thickness:...

17mm socket to fit 17mm x 5mm nut, with 24mm outer nut and hollow 11mm diameter internal bore. Also has a 16mm x 2mm bore recess. This was used to remove a 1/4 turn ceramic tap valve and the recess is to clear a locking clip. The socket has a very...

I designed this water bong to fit a 17mm or 11/16inch socket x: 49.4848 y: 79.5423 z: 202.0101 wall line count: 5 infil 5% type: gyroscope print time: 10hr 29min

A versatile 17mm socket designed to fit a 17mm x 5mm nut with an outer diameter of 24mm and a hollow internal bore measuring 11mm in diameter. The socket features a 16mm x 2mm bore recess, allowing for easy removal of a 1/4 turn ceramic tap valve...

... is required. Update: Because I don´t like supports, I have made a two piece design. Print the files switch_panel_mount_17mm_2piece_left.stl or switch_panel_mount_17mm_2piece_right.stl without any supports. ...Use a screw M3x16 to connect the parts.

... required. Update: Because I don´t like supports, I have made a two piece design. Print the files switch_panel_mount_17mm_2piece_left.stl or switch_panel_mount_17mm_2piece_right.stl without any supports. ... Use a screw M3x16 to connect the parts.

This is a 17mm ball mount designed to fit onto the center of the dashboard on a 3rd generation Toyota Tacoma, above- or next to the infotainment screen. It requires some double sided tape to install and is best printed in PETG or some other heat...

This is a remix of the two following things: https://www.thingiverse.com/thing:4329397 Mavic Air Controller GoPro Clip Mount by Pyotr -and- https://www.thingiverse.com/thing:5499561 17MM GPS BALL MOUNT by Alien_Loaf I had a heavy-duty mounting...

Handle designed to accommodate a 17mm hex-nut, awaiting 3D printing completion.

It will work for any camera that fits within a square shape (approximately 2-1/2 inches wide, 2-3/4 inches high) and features a 16-17mm ball and a 5/8 inch (approximately 16mm) slot-type camera mount. The standard ball size is reportedly 17mm, but...

## 17mm ball attachment for Plasterboard(Gypsum Board) wall famous in Japan. **ホッチキスで壁（石膏ボード）に固定する17mmボールアタッチメント** Punch four staples in each of the top and bottom two hollows, totally 8 staples to fix it to the wall. The example in the photo...

Clips onto the back of the following tomtom models: START 42, START 52, START 62, VIA 52, VIA 53, VIA 62 The model obviously just provides 4 screw holes and not a ball mount, this is because you also need to print this model...

Also, I had to print at 96% to get the ball size to print 17mm, ymmv. To install, start with fitting the single nut in to the slot in the vertical piece with the 17mm knob on it. Then screw it to the bracket from the side that only has 1 recessed...

just updated the ball to the size i needed in tinkercad. ...also made a version with the rings being 2mm thick vs the original 1mm.

iPhone 6 With Case Ball Socket Mount This iPhone 6 With Case features a sturdy 17mm diameter ball socket + cap, perfect for mounting on Amazon where the ball mount itself can be purchased by searching for 17mm ball mount. ## Print Details Printing...

......To reinforce the area, I thickened it substantially. In this instance, aesthetics were not my primary concern; functionality took precedence. Notably, the revised design still nestles perfectly onto any mount that relies on a 17mm ball for alignment.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/bN85PEJNUnH

A versatile ball-and-socket camera mount designed for customization. It can be adjusted to meet specific requirements. I used this mount in conjunction with http://www.thingiverse.com/thing:120272 to secure my PS Eye cameras within a VR setup. After...

On that, it has a 15mm ball socket (attached and tightened by screw, which is why this is a half-sphere) which allows you to move and rotate the camera... so I figured, why not connect THAT to the camera arm, instead? This should work with a 15mm...

On that, it has a 15mm ball socket (attached and tightened by screw, which is why this is a half-sphere) which allows you to move and rotate the camera... ...so I figured, why not connect THAT to the camera arm, instead? This should work with a 15mm...

The TX02 Ball and Socket Joint Mount provides a quick and easy way to adjust the camera's angle, while also ensuring excellent airflow for optimal cooling performance.

Based on the customizable mounts by MoonCactus and the Ball and Socket by Antscran, we've developed a Nikon KeyMission Ball Socket mount that's compatible with GoPro. ... Now you can seamlessly integrate your Nikon KeyMission 170 or 360 with any of the...

Based on the GoPro customisable mounts by MoonCactus and the Ball and Socket by Antscran here is the Nikon KeyMission Ball Socket mount to GoPro. ... Now you can use your Nikon KeyMission 170 or 360 with any of the existing GoPro accessories !

Many are available online, some can be printed, for example:https://www.printables.com/model/631085-apple-magsafe-17mm-male-ball-car-mount...