14x1 lh thread adapter 3d models

The garden hose side uses a rubber washer (like all garden hose connections) and the pipe thread side uses a standard PVC hose bib adapter. Full open-scad source code is supplied so you can compose other types of adapters you may need. ...In scad,...

This if for LH MP9

I designed this adapter for a 13.5 PG cable gland to a 3/4" pipe thread, for example to seal the cable entry on a Vivotek camera junction box (AM-713_V01).

This is an adapter designed to fit a hotshue mount into a mic stand or a camera tripod, depending on the size of the thread, you have two files to choose.

I designed this adapter for a 13.5 PG cable gland to a 3/4" pipe thread, for example to seal the cable entry on a Vivotek camera junction box (AM-713_V01).

The Meade ETX telescope's rear port is converted to accommodate an accessory with a T/T2 (M42x0.75) female thread, requiring a 1-3/8"-24tpi male adapter.

... fit snugly over it. This adapter effectively bridges the gap between the two components by linking the Hemingworth cap to the base of the OESD thread spool. ...As a result, it elevates the cap by several millimeters, ensuring secure compatibility.

... the photos. I tried the "cone" type and had difficulty threading a bobbin with them because the bobbin is very close to the upright spool holder on the 4411. With this adapter, you can both thread the bobbin and sew using the large serger spools.

This is an Adapter to put into an ikea TERTIAL Lamp and combine it with a Shure MV7 Microphone. ... It has an 5/8-inch male thread and also an 1/4-inch female thread. So it can be combined with a lot of stuff. ... Let me know what you think!

... tripod attachment point for Sergey_77's camera adapter. ...The thread in the original was the wrong size for my needs, so this is just a resizing to the 20-1/4 thread size needed for typical tripod posts found in the US, or at least in my house. ...

Print thread side up, 0.1-0.2mm layers, whatever fill required for a very simple part intended to replace the M10 threaded push-to-connect tubing adapter seamlessly. ...Make any requests and I can create one that fits more recessed into the heatsink...

Airsoft KJWorks MK1 Thread adapter / outer barrel with a 14mm ccw thread. ... There are three small prongs at the end, file those down to the exact size of your inner barrel until it slides in it easily and doesn't wobble.

Solidworks users can easily convert 1-1/4 - 18 thread to a KF25 flange adapter by modifying the existing design to match the specifications of the KF25 standard. To achieve this, Solidworks designers need to update the thread size and shape to...

Print these adaptations without supports, with the thread standing upright. Printing them solid is highly recommended. To avoid complications with stringing or blobs clogging the threads, print one at a time and use a layer height of 0.15mm or less....

Hose adapter useful for connecting a homebrewing wort chiller to a kitchen faucet that has a Delta sprayer head. The sprayer hose has a non-standard connector. Unscrew the sprayer head and connect this adapter to the sprayer hose. Use some silicone...

This remix of rosscadguy's DJI Osmo Pocket Wireless Tripod Adapter is designed for tripods featuring a 3/8"-screw, or alternatively, to pair it with a 3/8" to 1/4" adapter - just as I did. ...As a result, you can seamlessly integrate it into standard...

This is an angled adapter with a 1'' inner thread on one side and a 1'' external thread on the other. I used it to not bend the hose for a 6000l/h water pump for our pond.The adapter consists of two parts. The only reason it has been designed like...

Thread adapter for barrel threads on WE Dragon 7.0 (M12x1) to M12x1 internal (=M11x1) while also clearing front spikes. Used for Tracer adapter:...

... include a knurled section so it sits flush with the mount. To make this adapter, just scale down dominikjannis's 5/8" to 3/8" thread adapter (https://www.thingiverse.com/thing:2798672) by 97-99%. ...I scaled mine down to 98% and it fits perfectly.

This is a sturdy adapter to mount a typical electronic radiator thermostat head with M30x1.5 flange nut thread onto a Danfoss RAVL valve.\r\n\r\nTo assemble the adapter, slide it over the valve with the flange side facing the heater. The adapter does...

I made this to attach my RØDE NT-USB studio microphone to a monopod (SLIK monopod 350 featured in the images) to create a makeshift mic boom pole, rather than spending upwards of $20 on a machined brass thread adapter. This adapter has a 1/4" thread...

This adapter clamps onto the dovetail of a Wild M400 series macroscope and gives female M42 threads, allowing you to use a range of adapters to attach whatever infinity-corrected objectives you please (pictured with an m42-m26 adapter and a USMC 10x...

Remixed the original into this very useful adapter for 1/4 inches threaded stuff, like ring lights, cameras, etc.The base with the ball joint seems to be very common on AliExpress and such sites. ...It comes with a phone adapter clamp at the end which...

... 1/4" female thread LED Light Mount Spigot Adapter This adapter is recommended for printing with 100% infill for added strength and don't fully tighten the spigot screw as it may crack the mount. ...Approximately 25 minutes to print on fast setting.

AOSafety Thread to 40MM NATO (RD40x1/7) Adapter ============================================ This prototype design for a threaded respirator to 40MM NATO (RD40x1/7/DIN) gas mask thread adapter is created to help cross compatibility of commercial off...

M18x1.5 Inside to M18x2.5 Outside thread adapter for Lidl Parkside Lathe. I used the Lidl Parkside Lathe, but found out the chuck I had wasn't compatible due to a different thread size. Extenders with the same thread - M18 to M18 - were available,...

The threading on the pistol side of the adapter would force the adapter to cant off the main axis. The second flaw was the moat like recess that would cause the thread adapter to have the middle ridge extend past the end of the barrel. The barrel on...

This adapter and thread fits snugly onto a GP-5 gasmask filter thread, allowing you to create your own unique designs with the thread file provided. The filter1 file is specifically designed for use with goliath rotor styled filter files and replaces...

The thread is sturdy enough to hold the adapter very tightly, provided it's printed well and from a material sturdy enough. Same goes for the rail. I recommend 2mm walls (shell), 50% infill with gyroid pattern and PETG. Turn the fans off if printing...

... To ensure a secure connection between the arm and the enclosure, I've chosen one of these versatile adapter screws: https://goo.gl/vhsNz4. A small metal insert is used as a threaded receptacle to accommodate the adapter screw snugly.