140mm fan adapter 3d models

Online request for a 140mm to 4" fan adapter, here are two versions.

Versatile 120mm to 140mm fan adapter

I made this to adapt a 140mm fan in place of a 120mm fan in a desktop evaporative cooler.

Adapter for using 120mm PC fans with 140mm fan mounting holes. The standard one ca nbe used to mount with standard PC fan screws. ... The short one is to mount 120mm fans to 140mm radiator.

My power supply fan died, and turns out its a 135mm fan, hard to find and expensive. ...This mod is an attempt to adapt a 140mm fan and replace the failed 135mm fan. ... Category: 3D Printing

An adapter I made to allow me to replace my 10 year old 92mm fan with a brand new 140mm fan. Great if you really like the heatsink, but not the fan attached to it. ... I imagine this would also work if your case had mountings for 92mm fans, but enough...

I designed this Adapter to Mount a 140mm Radiator on a 120mm Mount. I can also be used to Mount an 120mm Fan on a 140mm mount. Made an Test_ Piece as request. ...Instructions .2 mm Layer Height .8 mm Shell Thickness .6 Bottom/Top Thickness 60mm/s Print...

This is an adapter to fit a 140mm fan in the 200mm slot in the top of the NZXT Phantom Case. ...I was unable to find a 200mm fan that would fit the top of the case so I created and printed this adapter.

I built this Adapter to Hold a 140mm Cooling Block on a standard 120mm Mount, making it easy to switch between fans and radiators. I created a Test Sample as per the request. To assemble, follow these steps. ... 1 mm Tolerance 4 mm Shroud Thickness 2...

... suddenly stopped spinning, revealing it was a rare 135mm model that proved difficult to locate and pricey to replace. ...In response, this modification aims to repurpose a readily available 140mm fan as a direct substitute for the faulty 135mm unit.

Needed to create a gap between the two fans on my AIO to fit the 4090 cable bend. ...This allows me to push one fan up by 5mm and another down by 5mm creating a 10mm gap for wires. It had slots for #8-32 flat screws. ...I'll post real pictures in a bit.

I built an adapter that converts a 180mm fan to 140mm, allowing me to install a fan on a triple 180 cooler made by Alphacool. ...I'm using this setup as an external cooling solution.

140mm fan shroud for ali-express mini PC. It cools both the outside and the inside. ... Supports required for printing.

mod de adaptador de 120mm a 140mm para hacer un deshroud en una nr200p

... can use to other cases. ... it do not require support to print. it increase the thickness of the fan by 16mm but it do not change the appearance of the case, it use the radiator screw to attach to the adapter and standar screws to attach to the case.

140mm FAN adapter for 240mm AIO cooler. You can configurable height, hole size, fan offset, tool hole for fixing. In my case, I use silicon pin for FAN, and screw for radiator. For fixing to radiator, there is no space for tools, so i make hole...

140mm Fan Arm Adapter for DimasTech Benchtable - 14.05.2022 added thicker holder +2mm

I had enough room to fit 2x 80mm fans above the stock 140mm fans that come with the Fractal Define 7 XL, so I printed an adapter to fit them into the rails in the 5.25" slot area. ... Good for that little bit of extra airlow!

Customized version of https://www.thingiverse.com/thing:735038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=735038

Customized version of https://www.thingiverse.com/thing:735038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=735038

Customized version of https://www.thingiverse.com/thing:735038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=735038

Customized version of https://www.thingiverse.com/thing:735038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=735038

Customized version of https://www.thingiverse.com/thing:735038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=735038

After examining Korzar's design for a 120mm fan adapter, I decided to create my own version for the Noctua 140mm fan I had been using for years. Although I drew inspiration from his design, I started from scratch as practice since I'm still an...

I made this adapter to connect an arctic-silent 140mm pc-fan to the ducting flange of the *secret jardin* DS growtent. **print with the pc-fan side laying flat! ** supports required. M4-screws required. ... let the chilis grow!