13mm to in 3d models

9mm to 13mm Gear

... joint with hose connects two parts together seamlessly. ... 13mm to 8mm in diameter, the outer side provides a secure fit every time. ...It's incredibly easy to print this joint, with no trouble at all - the maximum overhang is a manageable 45 degrees.

http://www.thingiverse.com/apps/customizer/run?thing_id=735213 Instructions Using the following settings: Number of Arms - Set to 5 units Chamfer Depth - Adjusted to 2 units deep Spool Diameter - Measured at 32 units wide Collar Thickness - Specified...

Fillet Gauge 13mm to 21mm

Adapter for G3/4" to 13mm Tube

Allows you to connect the Gardena microdrip 13mm system to an electric water valve. ...Thanks, Enjoy!

The Smart Control App lets you hook up your Gardena microdrip 13mm irrigation system to a power water tap.

A Remix of the 19mm-12mm hose barb adapter by denis_anfimov as when downloaded file noticed that the hole did not continue all the way through. ...Renamed to reflect hose internal diameter. 3/4"/19mm to 1/2"/13mm.

... annealing at 100C for 20 minutes to ensure an airtight part. ...While still warm run it through the female threads to clean them up. After the part cools dip in hot wax (paraffin) @ 100C to protect the PLA if you intend to use this fitting for fluids.

Copy of the fillet gauge by TnaTmr to be larger sizes. ...Re-modeled on Fusion 360. Original - https://www.thingiverse.com/thing:1184315 Prints in about 40 min ish.

Copy of the fillet gauge by TnaTmr to be larger sizes. ...Re-modeled on Fusion 360. Original - https://www.thingiverse.com/thing:1184315 Prints in about 40 min ish.

I have successfully connected the 16mm pipe reducer to the existing system, and a new 11mm OD to 16mm ID adapter has been installed as per your specifications. ...The reduced pipe is now fully operational.

NPT 1/2" to 13mm hose barb

Split Gardena MicroDrip 13mm to 4x 4.6mm. ...Thanks, Enjoy!

½ inch to 13mm barbed pipe adapter. ...I use this to connect my solenoid valves to the 13mm irrigation pipe which I use for the garden

The other end is shaped to accommodate a 13mm body bolt that has been coated with paint, making it slightly larger in diameter compared to a standard 13mm socket. As a result, when inserted into a non-painted 13mm bolt head, the fit will be loose,...

An adaptor for connecting 4mm drip line to 13mm poly tube.

Quick male coupling (water hose standard garden coupling) to male coupling 13mm gardena for garden irrigation

It works with Estes 13mm motors, and you can use it in lightweight rockets that use 18mm motors. Print in ABS for better heat resistance and lighter weight. Use a brim when printing. Use a piece of masking tape for a snug fit on rockets without a...

It is a rack to store drills from 1 to 13mm with a pitch of 0.5mm so: 1 1.5 ... ... ... 12.5 13

I'll split the Gardena MicroDrip 13mm into four separate outlets, each 4.6mm in diameter. Thanks for your help! ...Have a great day!

Gardena 13mm MDS to QuickConnect Adapter.useful as replacement for the pressure Limiter when used with low pressure water supply e.g. ...garden pump. 2 O rings are needed 9 mm x 1.7mm and 10.6mm x 2.7mm (As for MDS 13mm and QuickConnect)

It closely resembles the 'Ear Taper' guide that comes bundled with some kits, but as per a request from jkmills, I created this guide to gradually taper from 13mm down to 3mm. ***Make sure to read print settings before attempting to manufacture this...

Split Gardena MicroDrip 13mm to 4x 4.6mm.Thanks, Enjoy!Print SettingsPrinter Brand:PrusaPrinter: MK3SRafts:NoSupports: NoResolution:0,2Infill: 70 or moreFilament: Fillamentum CPE, ASA signal   Category: Outdoor & Garden

... not to make it fail. ...But that hook was a breeze compared to what it could have been, thankfully! I managed to get it done without too much trouble. Tinkercad link: https://www.tinkercad.com/things/5uHqG8hV6pB-screw-hook-adaptor-to-13mm-hex-nut

... water to drain out. ... I haven't learnt fusion yet so customised on Tinkercad and ran through an stl fixer and it had no problems. https://www.tinkercad.com/things/9lfwB72OrFq-13mm-to-4mm-irrigation-draining-hub-customisable to customise. ...

I created this adapter to enable the connection of standard 13mm and/or 16mm protective pipes to the AM2302 temperature and humidity sensor. This adapter allows users to seamlessly integrate their existing pipe infrastructure with the AM2302 sensor,...

... Letter Size, utilizing the 'Letters.dxf'. Precision tuning of Nut_Size to an optimal 13 millimeters. Crafting a precise message in exactly 13mm dimensions. ... The perfect fit every time, tool length optimized to exactly 10 precise measurements.

I made this to be able to connect a normal 13mm and/or 16mm protection pipe to the AM2302 (Temp an humidity) sensor. Here is a pipe that fits: http://www.biltema.se/sv/Bil---MC/El/Batteriverktyg-och-tillbehor/Flexslang-2000031415/ Print Settings...