123d models

twisting both wire pairs reduces possible crosstalk and possible issues from it. there are holes for zipties after each dragchain, use it to secure the wires but leave some wiggle room for the wires inside the dragchain, if they are to tight...

I have printed all of the parts and assembled a model which is shown. The "Dome" cover will fit over the Base Plate, and in turn a 1/2" piece of sprinkler pipe will fit over the tabs in the center of the Base Plate. The Mic Holder will fit over a Gen...

The current model is sized for a 28mm long motor, if you get a longer or shorter one a new set of files will have to be generated. If you do not have access to Inventor let me know and I can generate the files for your size...

Once I print and test it, I will update this with the final model and the STL's. I'm currently working on a new version with a removable tray for the Pi since I now plan to use a Pi4 with this project. I would not recommend printing this until I can...

Even if my model provides screw holes and additional holes to fit the screwdriver through, I don't recommend using them. The pillars the screws were originally drilled in are most likely already split at the top due to the weak plastic. You don't...

I haven't printed it yet, but the OpenSCAD model turned out pretty well. See the additional .scad file, .stl and the explanatory symbols image. The original bezel is dark grey with a textured interior except for the plinth and label obrounds. This...

The resulting "cylinder" is much stronger - I even tried to bend/break it without success. The hole piece was created with the following drafts and results : Bottom row, through holes (left to right) : 1/2° draft = very tight fit, very difficult to...

The model is amazingly easy to fly. https://www.youtube.com/watch?v=rsS5YetUQyA The video quality is less good - this time I had to film myself. <iframe width="684" height="385" src="https://www.youtube.com/embed/rsS5YetUQyA" frameborder="0"...

Update: -Ive added a FDM "optimised" file, as the other model did not have a perfectly even bottom which would have made probelms when printing the first layer on an FDM printer. -Ive updated the schematic and eliminated a mistake. -Ive added...

If you still want to print your own loc line, I used the models from [MinyMan644](https://www.thingiverse.com/MinyMan644) found here -> [Loc-Line Fittings (1/4", 1/2" and 3/4")](https://www.thingiverse.com/thing:3268462). I strongly recommend...

Legal notes 3D printable file and model ©2022 Bethesda Softworks LLC, a ZeniMax Media company. All Rights Reserved. This is an STL ONLY for 3D printing and not a physical product. Requires a 3D printer and knowledge of 3D printing to useSTL files...

Legal notes 3D printable file and model ©2022 Bethesda Softworks LLC, a ZeniMax Media company. All Rights Reserved. This is an STL ONLY for 3D printing and not a physical product. Requires a 3D printer and knowledge of 3D printing to use STL files...

A .3mf file is available along with the STL models.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it works best to drill a first hole and then insert a screw into that...

... ...Allows you to now place RepWinders in your newer model RepBox without having to Remove the Slip Rods!&nbsp;UPDATED 10/29/19Print instructions3MF File set up for Default .2 layer height Prusament PETG PrusaSlicer profile. Can be done in PETG or PLA.

While some complained about the expenses both in development of such tecnologies,a nd its application on the mech, the Fronc goverment applacate such concerns with the generous loan from the Alliance members.Gone is the troubling Andora-made gyro,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

The COMPLETE Thieves Guild bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Thieves Guild AdeptsVery little is known about the legendary Thieves' Guild in...

By the way, even though adding a vertical ring might seem counterintuitive, it does provide added stability while still maintaining the original model's benefits: no need for supports, and you can print directly without worrying about brim or...

Taller models have a tendency to cool in the middle and pull the bottom up at the corners. If your workspace/office is 75 degrees and you printer is not in an exclosure you should probably use some kind of adhesive. I found Glass+Glue worked for me...

 If you intend to use Sovol's SV06 Plus hotend, you'll have to get or make a duct that will work with the tall heatblock.I included a few models from Sovol's github, to include their extruder knob and extruder release lever, for no purpose other than...

Great model from Toshi_TNE. Remix it again to support free and no infill. (Original https://www.thingiverse.com/thing:3527806) <iframe width="560" height="315" src="https://www.youtube.com/embed/vPmPJOiqFYw" frameborder="0" allow="accelerometer;...

Great model from mz4250. Remixed to no base and support free again. https://youtu.be/J8bSrSSTLVE <iframe width="560" height="315" src="https://www.youtube.com/embed/J8bSrSSTLVE" frameborder="0" allow="accelerometer; autoplay; clipboard-write;...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size relevant to the...

* Supports: Yes (if using Cura we recommend using the [Tree supports](https://support.ultimaker.com/hc/en-us/articles/360012614559-Experimental-settings) option and adding a 'Brim' to help the Tree supports adhere to your print bed) * Rafts: Doesn't...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

the better the less likely it will grab but u can always use nuts on the other side even tho i didnt make a place for them to sit on the model since i had planned on using the threaded inserts but it will still work cause thats how i test fit...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

This helps with the strength of the threads as it will be printed length wise on the build placeThis gives more freedom to place pieces in any orientation, as well as add spacers between larger parts for more accents and individualityFixed stringing...

Print Settings Printer: Heavily modded Craftbot Rafts: No Supports: Yes Resolution: 0,15 or 0,20 mm Infill: 33 or 50 % Notes: Print both models in PETG with 3 mm thick walls and slightly hotter than usual, this should give you enough strength for a...

... with any light color and use a permanent black marker for the text. These models are not designed for dual-color printing. You'll need to print two Monster Ability Card holder v1. ...One is for the Monster cards, the other is for the shop cards.</p>