123 blocks uses 3d models

Use 3-4mm long motor screws. Add the flywheels and make sure they're aligned nicely and take into account motor shaft looseness when doing it. When inserting the flywheels on their shafts make sure the motors are supported against something by the...

Options used: panel_shape=1, orientation=1, border_width=1, pixel_size=0.7, thickness=0.5, grid_size=0.3, pixel_elongation=1. ... Picture details:...

Check for Understanding: Instructor should walk from student to student as they use the VFM. The instructor may encourage students to keep their fraction pieces in place so they can quickly confirm understanding and help correct students who are...

https://www.etsy.com/shop/StoneysMakerPlace?ref=l2-about-shopname Feel free to drop in or if you have a project for the home that needs some out of the box thinking I'd be glad to offer a hand and estimate. Here is my Etsy Page:...

http://www.thingiverse.com/apps/customizer/run?thing_id=49590 Instructions Using the following options: left_port2_custom_circle_radius = 0 back_port3_custom_circle_radius = 0 back_port5_custom_rectangle_width = 0 front_port2_custom_circle_radius = 0...

... No support. For best results, change the color at 10.2mm.For the board and the lid use the same parameters. Note : I originally publish this design in my Thingiverse page (https://www.thingiverse.com/thing:3077387).Enjoy :)  

-AUTO TRANSLATE TO ENGLISH- After 3 years of using my mobile charger (huawei P30 PRO) the connector had started to break slightly (surely my cat biting it and dragging on the ground helped) so I decided to print a protector. The regular models were...

Smaller resistor values triggers the reflector switch faster, but could also turn on the switch permanently.The circuit could also be integrated and wired up in an own plate before the solenoid.Instead of the reflector switch, a normal switch could...

Wood filament!Based on the top ornaments I designed the bottom ornaments and printed them with Sapelly wood filament. The problem, missing...

Length over all 170 mm.Couping hook fixed in newer VersionYou will need: 1 ea frame (rahmen)2 ea axle (Achse)2 ea sleeve (Achshuelse)4 ea wheel (Rad)4+x ea pin (Achsclip)2 ea support for hutch (KipperStuetze)1 ea hutch (KipperMulde) Prepare...

If you have the proper filament colors, no painting is needed. Don't let the number of pieces or my lengthy notes worry you, it's a reasonably quick print and very, very easy to assemble. The model is 140mm tall. Enjoy! Print instructionsRafts:...

The process of adaptation presupposes that practical aspects of printing the model using the FFF/FDM technology are taken into account, and the model's scale and cutting are chosen to ensure an optimum result of printing.3D PRINTING...

http://www.thingiverse.com/apps/customizer/run?thing_id=46884 Instructions: Using the following options: add_sub = 2, perimeter = -1000, qr_thickness = 5, per_h = 10, per_w = 3, round_corner = 1, tag_width = 80, qr_data =...

I will now write this text again with the same tone, voice and phrasing as the original text using active voice at all times, avoiding expressions such as 'Here is the spun text' and similars, removing any foreign characters, following the rules of...

Scrape the ribs lightly with a razor knife, or use a file, to adjust for snug fit. The tools plug works best in the front left corner, with the hole with rounded corners in the corner of the machine. ...</li> <li>Place UHU glue stick and tools in holes...

Now the outer surface of the extrusion is coupled to the drawer lip and the extrusion shift and resulting clicking is eliminated.&nbsp;Print InstructionsPrinted in PETG at 0.30mm layer, 10% infill.&nbsp;The STL file is a left cap which is mirrored in...

Once this is done the external Bowden drive can be fabricated using the original drive motor by mounting it on the outside panel. Then a new filament spool holder was fabricated and mounted on the outside of the cabinet. See Thingy - 780379 The...

#What To Print# For four-square, you will need to print: * 1x centrepiece * 4x edge * 4x corner #Plastic Pipe# You will also need 40mm plastic waste pipe for the frame - I used FloPlas WPO2 40mm White Polypropylene Waste Pipe. '40mm' pipes are...

Assembly As mentioned, this thing is intended to provide the model kit parts that can be assembled per Frank Cerny's plans which can be found on Rebeldroids.net Since the 3D printed parts might be a little thicker on the bottom, and I left them flat...

Directly soldering to the board will work but is not recommended)1x Roll of this silicone wire (Make sure it’s thin) https://www.adafruit.com/product/31641x Roll of thicker gauge silicone wire for battery (Depends on what your cell specs are)1x...

So please comment and post your results. The rest of the models are designed to print with support "touching build plate" and do not need "support everywhere" Depending on your printer and cooling of course. Files "should" load pre-oriented for best...

Surely it is possible to put a control through a simple encoder so as to have a precise clock after days, or use a step-by-step motor or a properly controlled servo motor. I took advantage of the suggestion in the comments to widen the dial, so you...

100g Filament i recommand ASA (PETG can be a little challenge to get rid off the supports)&nbsp;5x M3 x 10mm Countersunk Screws&nbsp;5x M3 threaded inserts&nbsp;6x Cable lugs...

He used this wealth to improve his properties and invest in various ventures, including the construction of roads and bridges in northern Scotland. In 1811, parliament passed a bill granting half the expenses of building roads in northern Scotland on...

Using the following options in customizer, create a unique version of http://www.thingiverse.com/thing:287025 Options include: Panel shape: 0 Pixel size: 0.7 Thickness: 0.5 Grid size: 0.3 Orientation: 1 Pixel shape: 4 Custom picture data:...

I set - all speeds to 50, (steady flux) - set the part fan to 0, - 235° tool temp, - 1.2 flow multiplicator, - no retraction - and I use prusa slicers 'avoid crossing' option. - bed temp is still on 60° like with PLA but that is no so important ...

Following in Sublime’s footsteps, Tim Rastall (https://plus.google.com/u/0/+TimRastall/posts) created the very popular Ingentis printer (https://www.youmagine.com/designs/ingentis-a-tantillus-variant), which is a larger version of Tantilus using...

Customized version of http://www.thingiverse.com/thing:287025 created using Customizer! ... The customized picture is composed of various RGB values, including...

I'm using Esun ABS+ with 20% infill and 0.2 resolution.For build and flight footage, watch my video&nbsp;&nbsp;If you want to source the parts, here is a list:Electronics1x Happymodel X121x NamelessRC nano GPS1x JumperRC T-Pro ELRSMotors4x 1202.5...

I printed the upper and lower parts in PLA and glued they using two-component glue.Please post your make. Thank you. :-)</strong></p><p>----------------------------------------------------------------</p><p>Update 24.02.2022:<br>Medium-Version...