123 block 3d models

Magnetic spheres are used to make 3D printed polygons that can be used as an educational math tool, a fidget device, or a unique set of magnetic building blocks.  The polygons can be used to make polyhedrons and other fun shapes.Triangles,...

A daring piece of architecture for The Loop area, Aqua comes off more as a massive sculpture than as a residential block in the crowded heart of the city. The name "Aqua" is in keeping with the nautical theme most of the buildings in the Lakeshore...

Only realised after looking at the connectors, I should have ordered a V2 - DOH!2022 Jan 12thI created a mount for 4 position terminal blocks. They accommodate 3-4.3mm fork connectors.The blocks position can be adjusted on one axis, depending where...

The 3010 fan being smaller can be a little more noisy ( I have used rasonable quality ball bearing fans rather than hydrualic and therefore are quite good) but due to its size it sits above the heater block much closer to the heat sink and therefore...

Here are more of my anatomical designs you might enjoy: Novelty: Wearable Spine: https://www.thingiverse.com/thing:4982223 Skull Jewelry Set: https://www.thingiverse.com/thing:4980129 Happy Halloween Spine: https://www.thingiverse.com/thing:4979522...

It lacks the flashy spires of Sears and Hancock, and instead goes for vertical stripes to add extra visual height to its already impressive stature. From a distance, the building feels like another boring grey 1970's stone block. But to really...

... the major axis of the ellipse coinciding with a diameter of the semicircle. Unicode encodes a crescent (increscent) at U+263D (☽) and a decrescent at U+263E (☾). The Miscellaneous Symbols and Pictographs block provides variants with faces: U+1F31B

Remove supports at the marked locations Remove the top bridge-layer marked with green, this is only there to enable the printing of the grid and will block airflow if not removed. BLTouch Front Mounted To fit the cover over the front mounted...

You will need to print: -Top Replacement pieces for FFC Pro: FFC PRO Vent Top Left and Right (2 pieces total) -Duct to mount to top of new FFC Pro Top: 4in Vent adapter from ffcp01 file duct.mount (1) -A 120mm Fan to 4in Vent Hose adapter (1)...

I will say that its best to fit it all together and make the needed screw holes etc before taking it apart to fit all the electronics parts in there. Custom Section Additional Parts Needed Parts for assembly AA flashlight (...

The measurement is relative to the height it extends above the surface of the badge.[background color] and [foreground color]These dropdown boxes change the colour of the badge background and the contrast colour which effects the border , logo and...

I used Cura's support blocking feature to do that. I also found that since the original Rpi Case was very tight, and I had to scale by 102% even with PLA (monoprice PLA+), to get the parts the same dimensions as the model. If you need to scale, be...

... put the base/ring flat on some sandpaper and sand it down. If a ring doesn't fit well into a base or other ring, check the tabs/slots for small pieces of resin which may be blocking the connection. ...This can happen during the cleaning process.

This allows more travel on the mechanism and helps smaller keychains make contact with both magnets.I've included GCODE for v1.1 linkages, or you can download the full 3mf.Included a (hidden) mounting standoff block in the 3mf to help stick to a...

PLA is less suitable as the fan shroud is too close to the heater block.Slicer settings:The model is oriented in the intended printing orientation0.4 mm nozzle (0.6 mm nozzle can be used when using the Arachne slicer engine in Cura 5.0 or higher).4...

They will need to be setup for stall detection during homing. Required Hardware. 1 x 100mm TR8 Leadscrew NEMA17 Stepper Motor & Nut (afflink). 1 x 110mm MGN12 Linear Rail (afflink). 1 x MGN12C Carriage Block (afflink). 1 x Brass Brush - White...

^_^ Update 1: I quickly realized that finding paint bottles in the rear was pretty hard because the labels were blocked by the bottels in the front. So I added two more designs to elevate them and making it easier finding...

https://www.thingiverse.com/thing:2545713 My printers y stop switch touches off on the bearing block so that is why the one design has a wall on one end. That also gives them a more stable base for printing on end which gives a smoother saddle for...

Even though it has a lot of material around to make a good and strong fit around the case, it still doesn't block the front venting holes. It's designed to be used with this mains socket: ...

Also, drill out the blocked holes on the bottom hub. These made it easy for your printer to print the overhangs.</li> <li>Get some 35mm M4 socket-cap screws and insert them into the recessed holes on the bottom hub. Align them with the empty holes...

Suggested weight range 450-600grams balanced on the rear of the front landing gear blocks. Required print bed size=235mmx235mm "Ender 3" or larger. 6/27/2022:(This is a test release only) we are still working on this model, however... we felt it...

It only needs to prevent the lens from unscrewing from the tube by blocking sideways movement (so it's fine for it to be loose).Printing instructions:PETG or ABS recommended0.1mm layer height2 perimetersNo supports or brimAvoid ending up with...

I had a problem during cold temperature where the shorter version was blocking the motor because the driver causes too much pressure on the motor axle. UPDATE 2nd of Dec. 2021 - if using the optional temperature sensor (see link below) please...

There is no shortage of covers for the Mean Well LRS-350 power supply, but I couldn't find one that was quite what I was looking for, so I decided to create my own. 2019/09/24: Added Fusion 360 Source Files Print instructionsThis design was made...

・I installed 3Dtouch on KINGROON KP3.・The duct support "KP3_DuctSupport+3Dtouch.stl" to which 3Dtouch can be attached is a remix of this EZABL KP3 OEM Mount with...

height gages, measuring blocks, etc.), with the following standard sizes: 1/8", 3/16", 1/4", 3/8" & 1/2". The holders are free standing and peg board compatible (3" spacing on the peg board hooks). There are four object files because there are four...

you can use one of these in place of one of the USB power boards if you are powering a bed heater that draws more than the Duet's 18A circuit can provide: http://amzn.to/2ozFxFg Lugs for two 5-pin Wago connectors (221-415) to be used as terminal...

The blocks fit in real tight and the whole thing is really stable. It takes some effort to get them apart - but no glue required, and you can change it around. The other bits on the base (in the video) are previous test pieces or bits that may be...

Of course, this model is for “off-road use only” :) Depending on your vehicle, this mount may block very important, time sensitive, critical vehicle information or warnings. USE at YOUR OWN RISK. Use not permitted on Tuesday evenings between 7:20pm...

If you print cleanly, the imitated terminal block fits perfectly into the bottom of the shuttle - alternatively you have to file it down a bit.First the angle was fixed to the wall, then the white base frame was pushed on, the black support on top...