120mm distro plate 3d models

Upon successful installation of the Liandynamic D5 pump and side-mounted distro plate, these motherboards are expected to function flawlessly: ROG STRIX Z390-E GAMING; ROG STRIX Z370-F GAMING; ROG MAXIMUS X HERO; ROG STRIX Z370-H GAMING; ROG MAXIMUS...

Simple board plate for a Falcon F8 Distro Board.

This is a cap I made to cover the label and help hide the cables coming out of the front of the pump on the front of the EK Evolv X distro plate. ... If I printed it again I would probably go 15% infill

The distro plate is compatible with specific motherboards: ROG STRIX Z390-E GAMING, ROG STRIX Z390-H GAMING, ROG STRIX Z370-F GAMING, ROG MAXIMUS X HERO, ROG MAXIMUS X HERO (WI-FI AC), ROG MAXIMUS HERO, ROG STRIX Z370-E GAMING, ROG STRIX Z370-H...

The distro plate works seamlessly with these motherboards: ROG STRIX Z390-E GAMING, ROG STRIX Z390-H GAMING, ROG STRIX Z370-F GAMING, ROG MAXIMUS X HERO, ROG MAXIMUS X HERO (WI-FI AC), ROG MAXIMUS HEROS, ROG STRIX Z370-E GAMING, ROG STRIX Z370-H...

This distro plate works with these motherboards: ROG STRIX Z390-E GAMING, ROG STRIX Z390-H GAMING, ROG STRIX Z370-F GAMING, ROG MAXIMUS X HERO, ROG MAXIMUS X HERO (WI-FI AC), ROG MAXIMUS HERO, ROG STRIX Z370-E GAMING, ROG STRIX Z370-H GAMING, ROG...

The distro plate works with these motherboards: ROG STRIX Z390-E GAMING, ROG STRIX Z390-H GAMING, ROG STRIX Z370-F GAMING, ROG MAXIMUS X HERO, ROG MAXIMUS X HERO (WI-FI AC), ROG MAXIMUS HERO, ROG STRIX Z370-E GAMING, ROG STRIX Z370-H GAMING, ROG...

Custom Distroplate for D5 pump

This is a replacement waterway/distro plate panel for the original Lian LI PC-O11. ...I haven't CNC'd this yet, waiting on my Shapeoko 3 XL.

Assembly is pretty straight forward, you slide the pump holder on the pump, place the o-ring holder on top and the o-ring inside it and mount them all to the distro plate using the original bolts. Disclaimer: This is not the intended use case for...

I required a basic honeycomb 120mm fan cover plate and I managed to craft one successfully.

I uploaded a 120mm lock plate design specifically tailored to fit neatly into standard door frames using FreeCAD software, allowing for easy and precise modeling of the locking mechanism and its surrounding components.

A plate to secure a 120mm fan mount, keeping dust from entering your PC case is a must. Two millimeter screw holes are drilled into it. Note that I haven't built mine yet, so I'm unsure if the holes will align perfectly. ...If you've constructed one and...

Compact Cooling Solution: Customizable Fan Plate for Optimized Airflow Control Engineers now have a versatile tool at their disposal to fine-tune airflow within computer systems - a 120mm fan blanking plate that can be easily tailored to meet...

This is a magnetic stir plate based on a 120mm fan, powered by 12 volts. I wanted something larger and more stable than the 80mm units. It uses a PWM speed controller from eBay, either with or without an LCD. At high speed, it will throw the magnet,...

I designed this mount as a simple way of attaching a 120mm fan to 8040 extrusion. Along with a duct that can be found elsewhere it makes an easy way to mount fans for wind simulation on a racing rig. ... Its my first design, and I hope someone finds it...

This system is fully compatible with both the Lian Li o11 Dynamic and the more advanced Dynamic XL models.

Barrow Distroplate for P600s and Evolv X PHP600S-SDB 99% accurate

Barrow Distroplate for P600s and Evolv X PHP600S-SDB 99% accurate

Combine this component with a 120mm fan and two neodymium magnets, each no taller than 5mm, to create a sleek and modern magnetic stir plate.

Hello Kitty distro Shop

Install 2 120mm fans - one pushing air out and the other pulling it in. If desired, remove the top case of the power supply and its fan, but exercise caution to avoid exposure to hazardous voltages. Utilizing standard 12-volt fans and an...

The fan joiners are a remix of halilgrgn51's design (https://www.thingiverse.com/thing:4601769), but thicker where it sits on the build plate to help with adhesion. ... 0.20mm layer height 0.45mm extrusion width for perimeters and external perimeters...

I replaced the stock Mini Delta fan with a cheap generic 12v 120mm fan because it's extremely loud. The printer is now completely silent when idle, making it much more enjoyable to use. To install this new fan, you'll need to add the appropriate...

&nbsp;Put your smooth, textured, or otherwise outfitted flex plates in this holder and they'll always be ready to use.Holds six (6) 120x120mm plates, single or dual sided; slot size is about 4mm minus any shrinkage that may occur. ...&nbsp;</p><p>I...

I remixed this F8 Distro holder to mount the board long ways in my case.

This is the Falcon Distro connecting directly to P10 brackets, featuring a secure wedge and snap-in clips that firmly grip the board in place, eliminating the need for screws. ...Please don't hesitate to point out any adjustments required!

100% ready to cut.Perfect sizes.Enjoy.;)

I designed this drain to quickly empty the loop without having a special valve or flooding the case. ...The funnel fits the cutout for mounting a 140mm fan.

Outdoor box for falcon f8-distro power distribution board. The board mounts in the screw holes and I have 3 x 1/2" wire glands (4 leads in 2 glands) and (1 for the main power). The lid is tight-fitting and stays on I added a lip to help keep water...