10l coke bottle 3d models

I'll be using it to place my cup of coffee or bottle of water, as those are my drinks of choice. My print time for this model was 2 hours and 43 minutes. The coaster measures a standard size of 100 by 100 by 5 mm, making it fit perfectly in my...

A bottle of hand wash provided the spring for this project. The base used is a perspex block designed specifically for rubber stamping. When drilling and tapping holes, do so slowly, as excessive heat can cause distortion around the hole. If you...

On picture the new Sandamnn Mini Car on tracks.This is the Sandmann Planierraupe ( Bull dozer).Sandmann driving the small bull dozer on building construction site.The same scene as on the moving a tree and delivering a premade bath room module hung...

Mechanical Parts List: 1" Aluminum Extrusion Lengths: https://www.mcmaster.com/#47065t101/=1cxkx44 - (4) 425mm X Frame - (4) 552mm Y Frame - (4) 572mm Z Frame - (16) Corner Brace for 1" High Single Rail, 1" Long:...

**Flux Stand**: A stand for holding flux bottles or other small items. 2. **Mobile Hard Drive: 2.5 Inch USB 3.0 SATA**: A protective case for a 2.5-inch hard drive with USB 3.0 and SATA interfaces. 3. **Magnetic Plate for Little Things**: A magnetic...

Thing #3844. Also I modified the Spinning Gear Toy by dsegel , thing # 959386 for the gears in the feet and tip servos. Also Thanks to Six Pack o' Polymers by BenitoSanduchi Thing # 18407 for the bear bottle STL that I rescaled. Kongorilla's Arms , I...

PADDING_FLOOR_TOP=15; // red PADDING_FLOOR_LEFT=3; // green PADDING_FLOOR_RIGHT=3; // blue PADDING_FLOOR_BOTTOM=5; // pinkDisclaimerThe print does not come clean enough, even for 0.8mm, and some overhangings do appear, eventhough PrusaSlicer doesn't...

You can make visors from soft drink bottle plastic or laminating pouches. If you use laminating pouches, feed each one into the opening of the pouch as it runs through the laminator. Cut the curved surface to the visor pin positions with minimal...

Check out this actual testimonial: "I absolutely adore it!" - My wife (who hates most of my 3D prints) This charging station is designed to hold multiple devices simultaneously: - Multiple tablets up to 6" wide, including large-screen models like...

I just shove the tapered tip of the glue bottle in there and squeeze and run it around, then make sure the rim and sleeve are lined up and wipe the excess off with a paper towel.Print SettingsPrinter Brand:PrusaPrinter: I3...

Bethesda/id category case mod competition. More information here: http://www.mitchcerroni.com/2016/08/04/nuka-cola-pc-case/ Build logs: https://hackaday.io/project/13388-nuka-cola-pc https://imgur.com/a/R0Ow5 PC Specs:...

The "vase" these flowers are sitting in is actually from my voronoi bottle holder project. Future updates will include a better vase with room at the bottom to hide the board and batteries, and I'm planning on sticking with the voronoi technique...

It works like a top-blown flute or a bottle, where the angle and lip shape are crucial. If you've played one of those instruments before, you'll have an advantage. It looks similar to some Asian flutes but is missing a whistle on top that helps get...

I've kept the number of paints down in case someone wants to do this and doesn't already have dozens of bottles of paint around; however, there are probably better colors for painting Tiger tanks than my selections. The tanks were finished as...

The feeder consists of four components: a sturdy plastic bottle reservoir for syrup that could last up to ten years, a durable metal plate that won't rust and could also last 100 years, a rubber gasket between the metal and the bottom, and a cheap...

A single 5mm bracket holds a 300x100mm glass shelf with 5 full-size perfume bottles, with 5mm wall plug and 2.5x30mm screw. Post-Printing Please note... The shelf is not meant to reach the wall. ...If you want it, cut a recess...

The printed part houses a Snapple bottle cap that we click to annoy our friends. That click makes this simple print extremely useful for flash sonar. The glossy flat surface created by the bed when printing also makes it the perfect way to transmit...

This is an impressively detailed replica of the iconic Royal Baby BMX Junior designed specifically for young riders.\nThe highly accurate model was initially created from scratch within Blender 2.79b-Cycles software, which delivered outstanding...

By attaching components like a Beer Bottle Opener and an Arduino powered "Kajigg-o-Matic", it became an incredible ice fishing pole. All I had to do was sit back, crack open a cold drink, and let the Ice Kajigger take over. Thank you and enjoy! To...

I love my SodaStream but always wished that the bottle caps weren't so slippery. Especially when they get a little condensation on them, it can be pretty difficult to get them off. This cap has a knurled pentagon shape that is much easier for me to...

Yellow Liquid in plastic bottle with a red plastic cap. Highly-foaming washing fluid causes low skin irritation. This liquid soap is used for hand washing of glasses, plates, cutlery, and cooking utensils in a sink or bowl. Dishwashing liquid assists...

Solution: Based on extruded aluminum profiles (like those of 3D printers) I modeled a piece that is attached to the bicycle on the screws that come to place bottle holders (on my soul bike there are 2 pairs of these screws). Then I modeled the...

I used ½ cup of each vinegar and hydrogen peroxide and two tablespoons of salt. Lay the model flat and using a spray bottle, spray the mixture very thinly on one side. Allow it to dry and spray another fine layer. Continue under desired results...

- People who are already using the bottles can easily upgrade. I first started by designing a screw cap attached to the LED’s holder, but all possible alternatives where not printable according to the given guidelines. The procedure for embedding...

This holder is designed to sit in the buffer or crosslinker spots on the Aspect Biosystems RX-1 Bioprinter (1), and hold a 15 mL Falcon tube instead of the default 50 mL bottle. This is handy when testing small volumes of crosslinker, and it also...

This clever design can be mounted either vertically or horizontally, and its versatility knows no bounds: simply add more wall mounts as you need to hold more bottles. To give it that extra oomph, Print Settings were set to two sturdy shells with...

My Things: Woodstock - https://www.thingiverse.com/thing:2702669 Graffiti Independence for North America - https://www.thingiverse.com/thing:2695303 John Lennon Graffiti - https://www.thingiverse.com/thing:2688181 Water Bottle -...

This comes with an adapter that fits to a 75mm stainless bottle, which can easily be modified into an effective afterburner for this compressor. I used a 2000kv motor rated up to 3000w to power this compressor, running on a 6 cell lipo battery so the...

That black paint isn't overly sturdy, so I finished the whole cube with a clear lacquer spray. For the yellow cube with black letters, I used a cheap black acrylic paint in a squeeze bottle with a fine plastic tip to paint in the letters. Category:...

These prints are designed to convert the glass Voss water bottles into sleek dosing containers. They are designed to mount on a vertical surface using a cleat that is secured and the Voss glass holder can be lifted off for easy servicing. The cleat...