10 x 10 games 3d models

Remixed Vice by Joestraws (Thanks for the baseline) scaled up x 10. ...Main Screw, caps and handle turned so no support is needed.

This is a straightforward cover for the X-axis belt of the CR-10. ...If a stepper damper has been installed, it will slide into place without any additional components needed.

A crucial printer component, the latch for inserting light on CR-10 x-axis, requires precise printing settings to achieve optimal results. ... Print Settings: Printer Brand: RepRap Printer Model: RepRap Kossel Raft Requirements: Not Necessary Supports...

Another x-axis tensioner upgrade for your CR-10! It's been over a year since I first used this device, so it's definitely time to refresh the design. ...Check out this updated version: https://www.thingiverse.com/thing:2657365 To assemble this part,...

Small storage shed (8' x 10'). Initial design was to provide 3/8" behind the outside sheathing (owner specified). This was later v.e.'d for construction cost reduction. ... Also, shingle roof replaced the modeled metal roof due to local sub division...

Small storage shed (8' x 10'). Initial design was to provide 3/8" behind the outside sheathing (owner specified). This was later v.e.'d for construction cost reduction. ... Also, shingle roof replaced the modeled metal roof due to local sub division...

I've modified the CR10 X carriage to fit perfectly on the Lembasbrots 3 Wheel X Carriage after a thorough discussion about using CR 10 parts on the FLSUN I3 or I3 +. To use this modification, you'll need to print out the 3 wheel carriage first.

A simple adjustment of 10 millimeters along one axis can result in a 10x10 chain.

Movement tray for 10 32mm bases. ...Walls are 3mm high and 2 mm wide.

These printable alignment blocks ensure precise leveling of your X-Gantry on the CR-10 before leveling the bed. A V2 model has been updated with a deeper hole for the Z limit switch, as per user request. The long X-gantry tends to drift out of...

Because I just happened to have 10mm x 10mm x 4mm magnets at home, I decided to edit Dragongars excellent work to fit my magnets perfectly. Because these magnets are rectangular in shape, a separate lid is no longer required and I modelled it...

With the CR-10 X endstop sensor securely fastened to Mount Plater, your printer should now be equipped with a reliable and accurate sensor system. ...This setup will enable precise monitoring of the print bed's movement, ensuring optimal printing...

2018/10/30 10:00 CORREZIONE DI ERRORE: corretto errore sulla distanza dei fori del motore. 2018/10/30 17:00 AGGIORNAMENTO: aggiunta linea guida per t-slot. ENGLISH Tired of looking online for the models, I designed them myself, starting from the...

UPDATE 2019/04: I have added a new version of the tensioner part, Creality CR-10_X Belt Tensioner_Hebign.stl. This updated part is more durable and has less play for the pulley. I've also modified the imprint to match the screw head on one side and...

I had noticed that my CR-10's x-axis belt was running off track - the main issue being the idler, which was skewed off-center and forcing the belt to veer towards the back of the machine instead of tracking through the center of the x-axis bar. The...

Instructions: Using the Following Options: - block_width: Set to 2 - wing_end_width: Configured as 2 - roadway_y: Positioned at 0 - roadway_x: Positioned at 0 - stud_type: Selected as Solid - wing_stud_notches: Enabled Yes - roadway_length:...

These are printable alignment blocks for leveling your X-Gantry on the CR-10 prior to leveling bed. I have just updated a V2 with a deeper hole for Z limit switch based on one user's request. The long X-gantry is known to go out of level over time,...

Test sample for calibration of Extruder Multiplier, 40×10.stl: Verify Settings. This stl file has uniform wall thickness at 1 mm on all sides and a height of precisely 10mm. ...Measure carefully at last rows near top of component.

I've crafted a brand new carriage assembly that's a dead ringer for the Creality CR-10. ...This bespoke part was designed specifically to work seamlessly with your printer, ensuring optimal performance and reliability every time you hit print.

Scavengers, bounty hunters, and other adventurers operating within the realm of Z-10 frequently utilize a high-speed ship that excels in rapid maneuverability, despite its relatively weak firepower, which consists of precision-crafted blasters firing...

http://www.thingiverse.com/apps/customizer/run?thing_id=445850 Options are applied: $fn is set to 50 Battery count is increased to 10 units Wire hole diameter is removed Wire hook width is fixed at 1.5 units Battery diameter remains unchanged at 7...

Holds 10 Compact flash cards. The elastic bands sit in the indentation. There is no indentation on the lid top, so that the elastic bands can be grabbed to take off. ...The Base is smaller vertically than the lid so that the box isn't opened upside...

Additionally, it includes a 3200 Belted Series standard load 90° shaft eDrive™ variable speed VFD gearmotor with 0.75 Hp (0.55kW) de-rated to 0.50 Hp (0.37kW) for full torque throughout the speed range, 230/460 volt, 3 phase, 6-60 Hz, 29 RPM,...

Cube that is 10 x 20 x 30 mm. No more no less. ...For all your distancing needs.

A straightforward design is needed to conceal the x pulley portion and secure it into place.

Very simple photoframe 100 x 150 mm. ...It is just on wall using.

Adjusting Mechanism for the X-Axis Belt The device enables fine-tuning of the X-axis belt to prevent contact with the profile. ...A blue line is added to enhance stability and prevent bending of the part.

The Locker Gladston Mesh boasts gold rods and features an 80mm x 10mm aperture in its mesh design.

I spaced 5 of these out evenly and joined them together. ...I added 2 x countersunk screw holes for mounting options.

Unpack and set up immediately. ...To do this, carefully lift out the X-axis belt located at the bottom of the printer's carriage assembly.