10 gallon metal bucket with lid 3d models

If you're using 5-gallon buckets for container gardening, I've designed these stands specifically for the bottom of a standard 5-gallon bucket from Home Depot. I tested them with this exact bucket and found they fit snugly at the base while elevating...

... these lids for the 2022 Happy Meal buckets. ... The lids can hold an LED tea light to light up the bucket from the inside.TWO designs. One has a full rim and cannot be used with the handle. ...The second design can be used with the handle. 

Designed these lids for the 2022 Happy Meal buckets. ... The lids can hold an LED tea light to light up the bucket from the inside. TWO designs. One has a full rim and cannot be used with the handle. ...The second design can be used with the handle.

This is a 3 or 4 part grate you can place inside the standard 5 gallon bucket. There is about 30cm under the grate. This provides a platform inside the bucket so you can keep things separate from the bottom of the bucket. I put a layer of desiccant...

This fits over the top of 2 gallon buckets. It's a little bit tight, but not so tight that it can't get on the bucket top; just tight enough so that it won't fall off when jarred. It has a hole for the male outlet of pumps. the rings on the...

2 1/4 inch lid for 1/2 gallon jar like this one.

CNC cuttable 5 gallon bucket lid to fit Dust Deputy cyclone on top of.

... dropping these prints inside. Then, add two scoops of desiccant - and instantly, you have your own dry box storage solution in place. V2 boasts shorter legs that minimize space requirements within the bucket, providing a more compact design overall.

... collision so the so when the handle rotates and contacts the sides of the bucket, it will stop. - The STEP version is also included.- The link for the bucket listing is: https://www.lowes.com/pd/Encore-Plastics-5-Gallon-General-Bucket/3083565

... collision so the so when the handle rotates and contacts the sides of the bucket, it will stop. - The STEP version is also included.- The link for the bucket listing is: https://www.lowes.com/pd/Encore-Plastics-5-Gallon-General-Bucket/3083565

Most plastic 5 gallon buckets have a small dimple in the middle of the bottom of the bucket. I designed this stirrer to sit on that center dimple and rotate. I use 4 neodymium magnets which are 6.5mm diameter. Ensure the magnets are oriented so...

Five-gallon Bucket Assembly Created Using SOLIDWORKS 2018. I'm New to This Platform and Appreciate Feedback on Any Mistakes Made, Including Uploading, Titles, Images, Tags, and More. ...Looking Forward to Your Insights!

A low-poly 3D wooden bucket with a metal handle is available for use in Virtual Reality (VR), Augmented Reality (AR), games, and other real-time applications. The model features detailed textures suitable for close-up renders and includes normal...

This cyclone dust collector connects seamlessly to a 5-gallon bucket for effective operation. Included within this file package is a DXF file designed for easy cutting and assembly using a standard toolset, optimized for use with 3/4 MDF or plywood...

These are the inside and outside pieces used to turn a 5 gallon bucket into a ice cream maker. The outside piece is designed so that a piece of 2" pvc pipe can be glued into it. I printed both parts at 100% infill for increased strength. ...

This is a basic dust cyclone that you can add to cover of a 5-gallon bucket. The base and cover should be attached using some sort of silicone adhesive. ... I'd also recommend that you put silicone adhesive on base and hose fitting and around threading...

I took the diameters of the top of the bucket and the area where I wanted to cut my bucket and made a spacer that sloped from the larger opening to the smaller diameter for the top bucket. If you decide to cut the top bucket shorter, it can slip...

I measured the diameters of the top bucket and the area where I wanted to cut my bucket, then created a spacer that slanted from the larger opening down to the smaller diameter for the top bucket. If you choose to shorten the top bucket, it will fit...

... automatic watering. Four panels to a 5 gallon bucket, designed in is the ability to adjust the panels for different bucket sizes and soil heights, if the panels touch on the mating surfaces, add soil until it is 1-2" (25-50mm) below the bucket rim.

This is a simple bracket designed to easily clamp onto the edge of a standard 5-gallon bucket, holding a float switch that automatically shuts down the reverse osmosis (RO) system used for collecting maple sap. The bracket requires minimal assembly,...

After printing the tower base I noticed the bucket lid wasn't very thick and flexed a lot. So I designed this support ring to mount on the under side of the lid to help support the tower. ...It doesn't remove all the flex but it helps a lot.

If you choose to shorten the top bucket, it will fit snugly between the spacer and the bottom bucket instead of inside the spacer.\r\n\r\nNow they stack together at a greater height, allowing me to use fewer buckets as it grows.\r\n\r\nI printed with...

My students and I created this to tumble our metal-PLA filaments to polish them. It's the piece you bolt onto the bottom of a bucket, then put into the drill chuck. ...We were inspired by this video: https://www.youtube.com/watch?v=TAOju0CJWFo This...

... my spent brass. ...they are stack-able i didn't glue mine. it may be better if you did. print at 10 -20 infill i set the walls a 3. the stem is taller than the dividers it all holder itself together well. .308 .45 and 9mm is what i have in the bucket.

... ...The conversion process typically takes around 2 hours to complete, with the exact timeframe depending on the chosen printer settings. ... The design is straightforward and easy to implement, resulting in a secure fit that prevents leaks or spills.

Designed to sit in bottom of 5-6 gallon corn deer feed spreaders to help siphon corn to spreader opening.This design is a single piece I made to print on my Anycubic Chiron. ...Others welcome to remix into multi-part for smaller printers.

The original lid was jacked, seeing if i could build a replacement

I had some 1 gallon glass carboys sitting in my basement that were getting dust on the inside of the glass. So I made and printed these TPU caps to close them off from spider and dust. Works great. Slides right on and easy to pop off. ...I don't know if...

A highly detailed kitchen gadget model with all textures, shaders, and materials is available for use in your scene. Just insert it into your project. This model can be found in Archmodels vol. 18 and comes in various formats like 3ds, dxf, max, obj,...

A can won't immediately fall out when turned upside down. I printed it on a Prusa MK3 using the "ultra detail" settings with light infill to create an insulating gap. I used Hatchbox PLA.The print took about 21hrs. ...I'm sure you could optimize that.