10 duct fan 3d models

... to snugly fit within my 5015 fans. ...The originals were marginally too large to comfortably nestle into the holes. It seamlessly fits within the original RebelRousingProps fan duct designed for the CR-10: https://www.thingiverse.com/thing:2274499

Cut the original design into two equal parts, omitting the extruder cooling duct altogether. ...Provide support only at the lowest layer. Included is a CURA 3.3 generated g-code file optimized for printing on a CR-10, compatible with the 5015 fan model.

I've discovered a common problem with many circular fan ducts - the nozzle often isn't even remotely centered, so I built this one from scratch. To ensure optimal performance, I also designed the interior to cool the filament evenly on all sides.

This is a fan cover with holder for Neopixel / LED strips for modified Elegoo Neptune 2 printers that use the CR-10 FANG fan duct. The cover can be mounted on the Neptune's stock fan. There is a notch and an eyelet on one side to fix the cables of...

This is a fan cover with holder for Neopixel / LED strips for modified Elegoo Neptune 2 printers that use the CR-10 FANG fan duct. The cover can be mounted on the Neptune's stock fan. There is a notch and an eyelet on one side to fix the cables of...

Almost identical to the original, but 2mm taller to clear the heat block and silicone sock on Microswiss all-metal hot-end.This is the only fan shroud I use anymore; It provides excellent cooling on all sides of the nozzle and when printed with...

The mount is compatible with the CR-10 FANG fan duct. The mount is designed so that the bltouch is at the same height as the original holder from Elegoo. The sensor offset only needs to be adjusted in x and y. Two longer M3 screws are...

... ...The mount is compatible with the CR-10 FANG fan duct. The mount is designed so that the bltouch is at the same height as the original holder from Elegoo. The sensor offset only needs to be adjusted in x and y. Two longer M3 screws are required.

This is a remix of the "CR-10/Ender 3 Hotend Fan Duct" from pixarfanatic95. This differs from the original by: - a BLTouch mount on the left side of the duct - BLTouch Offset by: x= -32 and y= -9. - Elongated holes, so you can adjust the height of...

Additionally, ensure that the part fan duct is also protected inside when printing with PLA. Modified from Xitron's version to fit the CR-10 S4 printer specifications precisely. ... To achieve optimal results, print in ABS with 100% infill density...

Insert the flange into the duct and fix it in place with a cable tie (or a chain of them), insert 120mm Axial fan into the opposite side. There are no screws for the fan mounting, you must provide your own solution, or you can warm up the corners...

So this is probably my final fan mount for the stock hotend, and it's a good thing because it's also the most effective one yet, offering unparalleled visibility. You'll need: 2 x 50mm fans 3 x M4x20 bolts 3 x M4 nuts 3 x M4 lock washers (optional)...

I modified the Thingiverse model 2352237 by adding curved edges to the mounting brackets.

Da mein Bauteilkühler kaputt ging hier ein nachbau des orginalen ! Ohne stützen druckbar! Since my component cooler broke, here is a replica of the original! ... Printable without supports!

Stock Cooling Support matches the Hottend's performance, with a fan layer duct that provides consistent airflow.

Reworked and reinforced fan duct for stock Creality CR-10 Max. Holds securely in place with 3 M3x25 screws. ...Prints well without supports.

Reworked and reinforced fan duct for stock Creality CR-10 Max.Holds securely in place with 3 M3x25 screws. ...Prints well without supports.</p><p>Category: 3D Printer Parts</p>

Despite its massive appearance, with 3 perimeters and 10% infill, this fan duct weighs less than half of the stock metal duct. I mounted the fans by screwing directly into the printed holes, requiring no drills or taps. (Results may vary.) I...

Replace the boot liner's blanking plate with a light insert to illuminate more space in the vehicle's trunk. ... Reduced by 1 mm to prevent impact during printing.

This is a basic remix of the "bore 4.1 throat" hotend. It's slightly taller and wider than the original, so it blows where it should. It's not perfect, but it will do for now :D. The Bore 4.1 hotend has an all PTFE throat, which makes it unsuitable...

Creality CR-10 Smart Part Cooler 60mm Fan Duct Requires Cover V4 New modified version of my fan duct. Takes a 60mm fan and is designed to allow seperate air nozzles to be fitted over the duct. Nozzles still to come but take a bash yourself and share....

I turned the fan down in my slicer software to print at 60% fan speed and it's the same quality as stock but much much quieter. Ramps to 80% for bridges. Part has been installed for 3 weeks with no issues. Printing at 210c on the extruder and 60c...

... surface has been flattened. - The fan inlet has been reworked for better performance. - The back mounting arm has been modified for improved printability. - Some model issues have been fixed. ... Suggestions for further improvements are welcome.

I created this to complement [ozfunghi's CR-10 FANG OEM fan duct assembly](https://www.thingiverse.com/thing:2763931). It may also work with other assemblies if they feature the same mounting hole. My dial gauge is the top-ranked option on Amazon...

The default petsfang needed a lil modification to work with the red lizard q1 v6, i installed this on both my ender 3 and my cr-10 this was a great hot end! like all great hot ends make sure you properly install it/assemble or you will get leaks.

It is in the same exact orientation and position as the original, and is compatible with the standard EZABL fang mount positioning. Print Settings Printer Brand: Creality Printer: CR-10Rafts: No Supports: NoResolution: .2 Infill: 20 Category: 3D...

Single and Dual 4010 fan duct for CR-10. ...Ender 2,3, pro, 5 etc.

... ...Based on Hannoc's innovative approach, this design is compatible with both E3D V6 and Vulcano printers, although it has only been thoroughly tested with the V6 model. The fan duct will also work seamlessly with the CR-10 printer's original fan.

High-Performance 25mm Cooling Fan Duct for R/C Racing Cars