1.5 inch pipe 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=279111 Design Your Unique Piece Using the Following Settings: Use the Given Options to Shape Your Design: Inner Height: Set at a Standard 35 Cap Diameter: Optimized at 49 Outer Height: Maximized...

This is a pipe holder designed to mount a 1.5 inch truss pipe for lighting to a surface using #6 drywall screws. The inner diameter is 1.51 inches, it holds 2 inches of pipe, the base is 4 inches by 0.5 inches thick. ... I'm using this to mount a truss...

For PVC projects that call for Schedule 40 1.5-inch T and elbow fittings, this fits snugly onto the OD of most PVC fittings of its size. Note that this is not intended for use on the pipe itself. If you're working with fittings that boast raised...

Print in a uv stable filament such as PETG or ASA. ...A bolt through the mount and pipe is recommended. ...I overbuilt this mount because it is a big investment that it will be holding.

It was specifically designed for PVC pipe legs for the IKEA Linnmon tabletop, but it can be used to add a foot to any 1.5 inch PVC pipe. ...I have also made matching mounts for the Linnmon tabletop PVC pipe legs that can be found here. Buy me a...

### Description This foot is designed to allow you to use 1.5 inch PVC pipe as legs for any project without scratching floors. It was specifically designed for PVC pipe legs for the IKEA Linnmon tabletop, but it can be used to add a foot to any 1.5...

Print two of these, then cut your 1.5-inch ABS pipe [1] to size. In the image, it is being used on top of Prusa Enclosure using IKEA LACK side tables [2]. Should be printed with as little as 5% infill as long as the bottom feet are 90%. You can use...

This leg mount is designed to allow you to use 1.5 inch PVC pipe as legs for an IKEA Linnmon tabletop. ...I have also made matching feet for the PVC pipe that can be found here. Buy me a coffee :) - Thangs - Thingiverse

### Description This leg mount is designed to allow you to use 1.5 inch PVC pipe as legs for an IKEA Linnmon tabletop. I have also made matching feet for the PVC pipe that can be found [here](https://www.thingiverse.com/thing:4605470). ... ###...

This adapter enables you to attach a garden hose to a 1.5 inch PVC pipe coupling. There is enough tolerance to allow for sealant or a gasket. For reference, it's the green object in the printer and I used a piece of rubber glove to form a gasket. ...If...

To make this design globally compatible, I standardized the width to a uniform 50mm, leaving a tiny bit of wiggle room when using standard 1.5-inch pipe. This means you'll still need to sand down the ends after cutting. This miter box is designed...

To make it globally-minded, I standardized the box's width at 50mm, which gives a tiny bit of wiggle room when using standard 1.5-inch pipe. However, this won't be a major concern since the ends need to be sanded down after cutting anyway. This...

This creation was crafted using Tinkercad's robust platform. ...You can easily edit it right now by visiting https://www.tinkercad.com/things/2RdLkFZ6wJ7.

The process that involves reducing the size of the hydraulic jaws is termed as hydraulic jaw compression. ...This is achieved through the application of pressure which reduces the volume and consequently compresses the jaws.

Here is a set of curved washers for a 1/4" bolt in 1.5" ABS pipe. I designed this to secure an eye bolt, allowing you to attach a rod holder to your float tube securely. The inside washer features a hex recess for a 1/4" nylock nut that's press-fit...

Customized version of https://www.thingiverse.com/thing:1720245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1720245

Customized version of https://www.thingiverse.com/thing:5590487 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5590487

I wanted to add the ability to adjust and level my desk I was making with the PVC pipe. I designed it so that all you need is a 3/8" or 14 mm nut and bolt (I'm using a 3 3/4" long one myself) and then a flat foot (I used this knob for this...

This is a clone of an commercial reductor.

This is the same design as the 1.5 inch truss pipe mount, but instead accepts a 38mm bolt and wingnut for clamping and easy removal. ... For pipes that are exactly 1.5 inches, wrapping the end once or twice with electrical tape will help improve...

For every extra middle section added, the overall pipe length increases by 5 inches. 4. To achieve a realistic finish, spray paint the model with textured paint to conceal layer lines. 5. Follow up with a metallic paint of your choice for an...

This is a wall mount for cable management that has an outside diameter of 1.5" when secured squarely to a flat surface. ... Print Settings Printer: Elegoo Mars Rafts: Doesn't Matter Supports: Yes Resolution: .2mm ...

Description: * Pipe size: 1" to 4.5" * Designed to fit standard print bed dimensions (110mm x 110mm x 110mm) * Minimal support required * Engineered to resemble industrial pipe (black iron pipe) in appearance * Custom 45° angle threads reduce the...

The gravity die-casting is carried on to fabricate 1.5 inch 4 way pipe fitting.

This coupling connects two 1/2-inch NPT threaded pipes, hoses or fittings. ...Measuring approximately one inch in length (24 millimeters), it securely engages NPS threads while providing a leak-free seal with the aid of thread sealant tape.

Remix of https://www.thingiverse.com/thing:4297295 Resized and optimized for 1.5" SCH 40 pvc pipe. Dust collector blast gate / shutoff valve. Requires one M5x15 bolt, washers, nut. Or M5x20, washers, nyloc nut. Qty 3 M3x10 bolts with no nuts. Drill...

Remix of https://www.thingiverse.com/thing:4297295 Resized and optimized for 1.5" SCH 40 pvc pipe. Dust collector blast gate / shutoff valve. Requires one M5x15 bolt, washers, nut. Or M5x20, washers, nyloc nut. Qty 3 M3x10 bolts with no nuts. ...

Remix of https://www.thingiverse.com/thing:4297295 Resized and optimized for 1.5" SCH 40 pvc pipe. Dust collector blast gate / shutoff valve. Requires one M5x15 bolt, washers, nut. Or M5x20, washers, nyloc nut. Qty 3 M3x10 bolts with no nuts. Drill...

Faucet adapter converted to 1/2 inch NPT, matching showerhead size requirements.

Adjustable Multi-Purpose Pipe Grip Arm designed to fit 1-inch (27.5mm) or comparable piping, secured by 4.5mm bolts compatible with M4 Allen screws.