1 inch half pipe marker template 3d models

I needed to mark out half of a 1-inch PVC pipe on material to cut. It would have been easy to saw a small section of pipe for a tracing template, but where's the fun in that? :) This template is bevelled so any sharpie will fit and give you a nice...

This is a half in pipe clamp/bracket. I used #6-32 X 1-1/4 in Machine bolt and nut for the two tighting devises. The bolt sticks out of the pipe clamp a little bit but if needed could be cut down. ...

Supports for 1/2 inch piping, was doing some plumbing under a deck and realized I didn't have any copper straps to achieve this function. No risk of galvanic corrosion as plastic does not react with copper or any metals really. I used PLA with 40%...

I'm hanging a length of half-inch PVC pipe in the laundry room, which will feature a number of my [Mask Hooks](https://www.thingiverse.com/thing:4576273) This design is a simple plate to mount 1/2-inch PVC pipe to the unfinished ceiling of my laundry...

Paint, put around your pipes and forget about it. ...This can be any size but is set for 1/2 inch pex pipe. ...Penny tips for my thought?

This is a tiny piece that holds a ½ inch pipe, it needs glue or a screw to secure the pipe.It prints without support material.

Justin G0KSC supplies Stauff branded pipe clamps with his InnovAntenna commercially produced antennas however I've decided to build one of his designs from his website at http://www.g0ksc.co.uk/ and needed some pipe clamps so I decided to print my...

Hose clip for fastening 13mm (1/2") irrigation hose to surface. Original files were done in freecad and are attached, so it should be tweek fairly easy to resize this for larger hoses. ... Be gentle - this is my first thingiverse project.

1 inch x 1 inch half-hinge.2.54 cm x 2.54 cm half-hinge.

Updated the pipe diameter to fit a half inch PVC pipe

Basic clamp or holder for half inch poly pipe

Wall bracket for 1 inch pipe

This is an adapter for connecting a 2 litter bottle to a half inch pipe. ...Eventually using for pellet to filament maker.

This bracket is made for a 1 inch diameter pipe or tube. The holes are .1 of a inch. ...This allows you to drill to the size you need.

I needed a 1/2 inch to 3/8 inch converter for an impromptu tap handle. Couldn't find one so remixed a pipe connector real quick in 3D Builder. Printed with 4 walls and 50% infill to make sure it was strong enough to hold up to the use and weight of...

Air venturi in a 1" pipe to fit in PVC/ABS fittings.

This is just a test pipe flange. ...It worked pretty good for my little project.

I use this bracket to mount my Dustboot pipe Print Settings Resolution: 0.8 Nozzle Infill: 40%

Justin G0KSC supplies Stauff branded pipe clamps with his InnovAntenna commercially produced antennas however I've decided to build one of his designs from his website at http://www.g0ksc.co.uk/ and needed some pipe clamps so I decided to print my...

1/2" (half inch) stopper for blocking wall sockets while carrying out new installation work or emergencies or in general. Will post picture once I print and test out. Second version made which doesnt print support around thread. Recommend...

I needed to cut some slots in the end of some half inch aluminium pipe while making an antenna. ...the end of the pipe needs to clamp onto a thinner pipe with a hose clamp so I made a pair of these to use as a template and to hold the pipe in the vice...

They fairly short (20mm high) because the other tree markers I made kept getting in the way of people hands etc. I have only printed it at 0.3mm and it looks great. ...I will be adding bark-like effects to the sides of the tree, so a smaller layer...

Nipple male pipe 1 inch

1 inch PVC pipe holder for double pipes.

This is a mount to hold 1/2 inch copper pipe with one on each end. ...The diameter of the hole is slightly smaller than the actual pipe so you need to hammer the ends on.

My buddy requested a clamp to make cutting pipe easier, so I whipped this up with a base design of 1 inch, but scaling up by multiples 100 would allow this to be easily converted to other sizes

This is a 1.5 inch diamond template made for my wife to use for paper piecing. ...The sides are 1/4 inch wide for standard seam allowance and 1/8 inch thick for strength.

This is a 1.5 inch diamond template made for my wife to use for paper piecing. ...The sides are 1/4 inch wide for standard seam allowance and 1/8 inch thick for strength.

This time with copper pipe straps for 1/2" copper pipe. Blender file included. The first one ended up being a bit tight so I made a slightly bigger one in case you don't need it so tight. Btw regarding the photos. The wall I connected these to is...

So, we bought some 1" galvanized steel pipe from Home Depot along with some 1" curtain rod holders (hooks?). We have a 14 foot section on our patio and the longest pipe we could find was 10 feet. So, I made this little coupler to join two sections of...