1 4 turn fastener 3d models

Turn the lock piece 90 degrees and pull it into place, as shown assembled in Figure 1. To remove the fastener, follow steps 1-3 in reverse. Both the lock and the star have multiple holes that can be used with tie lines or nails depending on your...

This is a simple loop fastener for 1.5cm and 2cm width straps.

Fastener - Raptiye

fastener clamp

fastener clamp

Measuring at 1 and 1/4 inches, this Chumacera boasts a sturdy build for various applications.

... the straps behind it, keeping everything securely in place. I designed this fastener for use with straps that are 26mm wide and 1.5mm thick. ...It should also work well with thicker straps as long as they're not more than 4.5mm thick at any point.

... for a way to keep your cables organized or simply want a fun twist on traditional fasteners, these reusable fasteners are sure to impress. Assembly information can be found at Souzoumaker (https://souzoumaker.com/blog-1/2019/6/26/simple-fastener).

... cable organizer, etc. ...Same as the simple fastener (https://www.thingiverse.com/thing:3715863) but a cuter design. Assembly info: https://souzoumaker.com/blog-1/2019/6/26/simple-fastener Print instructionsUnassociated tags: 3d print Category: Tools

Slide Fastener Lock

Slide Fastener lock

Servo motor FS5106BAttached Fastener

Elastic fastening component replacement piece.

magnetic paper fastener for whiteboard

can use to put fasteners.

... The shape is a simple slot with two small holes for the rubber filament to pass through. Ninjeflex filament is available at https://amzn.to/2YeY4GU. For assembly instructions, visit https://souzoumaker.com/blog-1/2019/6/26/simple-fastener.

CATIA V5-6R2017 ONLY FASTENER CLECO

Replacement fastener for foldable/removable windshields.

Using the following options: build plate manual length: 100 build plate manual width: 100 center radius: 6 electron number: 79 hole pin radius: 3 mesh resolution: 70 pin cap gap: .45 pin cap width: 4 pin hole count: total (1-79) / multiple ring...

A handy little fastener by Swedish firm Ojap

... holes are absent. Full-wing style designs prevail. Technic holes are disabled. Notches for wing stud connection are provided. Curves features an ending height of 0 bricks. Slopes also end with no added height. Stud rescaling is adjusted to 1 block.

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: type = 1 weight = 11 groove = 1 diameter = 32 margin = 0.1 $fn = 50 cursor = 100 edges = 1

or more featherboards, usefull for resawing big parts on a bandsaw for example. For T-Track/T-Slot you can use a 1/4-20 hex bolt, the lenght depend of how many featherboard you stack. For miter gauge track, I provide an 'adapter' that works with...

... featherboards you stack. An adapter for miter gauge track can also be used with 1/4-20 hex bolts. In addition, a knob designed for a 1/4-20 nut is available. ...Remember to print with tough material (abs, petg, etc.) since this is a safety part.

I built a stronger fastener to replace the old one that had failed me. ...The upgraded fastener is significantly tougher and longer-lasting than its predecessor.

fully customisable closet fastener, I use it to my shoes closet

My fastener organizer was missing a drawer so I designed this as a replacement.

Use this bolt to fasten two holes at once Category: Sculptures

A Dzus fastener is employed to affix sheet metal panels on automotive and aviation bodies, providing secure attachments.