1 3 8 threaded rod 3d models

https://www.thingiverse.com/apps/customizer/run?thing_id=193647 Using the Following Options: head_type = hex nut_resolution = 0.5 thread_step = 2 slot_depth = 2 nut_thread_outer_diameter = 29 type = nut step_shape_degrees = 45 head_diameter = 12...

This is an alternate way to mount a RAMPS 1.4/Arduino Mega 2650 board to the RichRap 3DR using the 8mm threaded rod and M8 nuts for the spool holder instead of the 3mm stand-offs in the electronics mount which were weak and didn't fit the M3 bolts I...

To mount a RAMPS 1.4/Arduino Mega 2650 board to the RichRap 3DR using the 8mm threaded rod and M8 nuts for the spool holder is actually quite straightforward once you try a different approach. Instead of relying on the flimsy 3mm stand-offs in the...

Once the rod is heated, melt just the center of the PLA (polylactic acid) enough that it conforms to the flats or marks on the threaded rod. Then, let it cool completely in an upright position until the rod reaches room temperature. ...With this...

M3 PREMIUM vat holer for draining The height is fully adjustable with the rod I glued the coupling nut into the base and used the two flanged nuts to lock the tray into place I used 1 - 3/8 threaded rod 1 - 3/8 coupling nut 2 - 3/8 flanged nuts 1 -...

... before placing it in an upright position. The rod is heated enough to melt the plastic just at the center, allowing it to conform to the threaded rod's flats or marks. ...Once cooled in the vertical position, your rod will have a knob on its end.

Using the following options: Resolution: 0.25 Inner diameter: 9 Outer diameter: 16 Thread length: 20 Nut height: 12 Nut type: standard Head type: square Head width: 10 Drive diameter: 6 Countersink: 1 Facets: 4 Slot depth: 3 Slot width: 2 Texture:...

**Step 1: Prepare Your Stock Ender 3** Begin by carefully removing any existing screws or attachments from your stock Ender 3. This will give you a clean slate for attaching your trod guide. **Step 2: Attach the Trod Guide** Next, take your trod...

M8 Threaded Rod Spool Holder.

Using the following options to create a customized nut: - thickness: set to 2 mm - nut type: selected as standard - nut thread outer diameter: fixed at 7 mm - non-thread diameter: kept at 0 mm - socket diameter: set to 5 mm - nut resolution:...

Thread cap cover tube BSP 1/4 and 3/8 screw size.

Customized version of https://www.thingiverse.com/thing:1329750 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1329750

Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647

Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647

The extensions include: 43538 - 1/4-in Drive x 1-1/2 inch, 43539 - 1/4-in Drive x 3 inch, 43531 - 1/4-in Drive x 6 inch, 43532 - 1/4-in Drive x 14 inch, 43537 - 3/8-in Drive x 1-1/2 inch, 44264 - 3/8-in Drive x 3 inch, 44261 - 3/8-in Drive x 6 inch,...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following settings: nut_diameter is set to 12 slot_depth is set to 2 inches deep drive_diameter is set at 5 inches in diameter socket_facets are rounded out to 6...

Using the following settings: Resolution: high Dimensions: thread step size: 2 mm socket diameter: 5 mm resin resolution: 0.05 mm thread length: 25 mm non-thread length: 0 mm counter sink depth: 2 mm nut dimensions: 15 mm diameter, 6 mm height type...

I desired a sleek, uncomplicated spot to store my 3/8-inch and 1/2-inch ratchets, therefore I crafted compact wall-mounted ratchet holders.

Humans design a simple headphone hook that clips securely onto a desk ranging in thickness from 1-3/8 inches to 3.5 centimeters. ...A cleverly crafted 5-degree angle at the top ensures a snug fit, firmly clamping the hook in place on any surface it's...

The unusual combination of measurements is due to what was available at my local hardware store, including an M12 rod, a 3/8" axle, and a 10x3mm aluminum extrude. How I Designed This Fully modeled the threaded rod in Fusion to the desired...

This is model measured from physical part. ...Rod for zinc-aluminum cast 3 jaw chuck (48/50mm) with M12x1 thread and cone mating.

this take the 3 piece handle and converts it into 14 seperate pieces, -3 Top core sections -1 Bottom Core Section -9 Accent Pieces (the pointy bits) -1 Top Cap that interfaces with the hammer head -1 Bottom Cap that includes a hole for a 1/2 inch...

I took the ChaosCoreTech Model and split the handle up into the seperate pieces, but I kept the proportions the same. this take the 3 piece handle and converts it into 14 seperate pieces, -3 Top core sections -1 Bottom Core Section -9 Accent Pieces...

In this preliminary design, the blueprint of version 1.2 Eventorbot integrates a bracket for securely holding the threaded rod in place. The purpose is to enhance the robustness and stability of the Z-axis construction by substituting the easily...

I had a drawer full of 1/8", 1/4", 3/8" and 1/2" end mills. So, i made this organizer to reduce the amount of space taken up by the end mills. ... I cleared out a whole drawer with this thing.

Stepper to 8mm threaded rod Category: DIY

Ikea Skadis Pegboard Accessory: Easy-Reach Threaded Rod Holder

Instructions Using the following settings: Lip size: adjusted to zero Mounting hole diameter: set to three point two millimeters Number of sides on shapes: incremented by one hundred Base thickness: set to five units Thickness of lip: reduced to...

Customized version of https://www.thingiverse.com/thing:41003 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=41003

Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647