1 200 scale aircraft 3d models

PACK - 21 Battle Planes of WW2 (Vol.3, scale 1:200) - PERSONAL USE: 1) Aichi E13A Jake (Japan)2) Avia B.534 (Czechoslovakia) 3) Brewster F2A-2 Buffalo (USA) 4) Curtiss P-36 (USA) 5) Fiat G-55 Centauro (Italy) 6) Fokker D.XXI (Netherlands) 7) Fokker...

The STL files are in 1/200 scale (in mm units). N.B. Resin printer recommended. The final object sizes are: Length: 2.64cm (1.04in), Width: 3cm (1.18in), Height: 2.75cm (1.08in). For any difficult or question I am always available to give you...

... The model has only been printed thus far at 1:48 scale. *** Example printed with Creality water washable resin on an Anycubic Photon Mono X. The Model aircraft pictured in the Gif is for illustration purposes only and is not a part of the model.

These are 1:200 scale Panther tanks models that really stand out with their snap-in turrets, making them easy to assemble after printing and cleanup. Simply push in the turret slowly into the hull, and it will snap firmly into place without falling...

The STL files are in 1/200 scale (in mm units). N.B. Resin printer recommended. The final object sizes are: Length: 1.86cm (0.73in), Width: 2cm (0.78in), Height: 1.83cm (0.72in). For any difficult or question I am always available to give you...

Other Scale and sizes are available Example printed with Creality water washable resin on an Anycubic Photon Mono X. The Model aircraft pictured in the Gif is for illustration purposes only and is not a part of the model. ... Follow on Instagram for...

For more models and paid versions please visit my Cult3D profile: https://cults3d.com/en/users/guaro3d/creation Follow me on Instagram: @guaro3D This easy-to-print aircraft scale model requires no supports, just patience. The model is in 1/64 scale,...

1/200 scale Assembled in sections, 55 inches overall, over four and a half feet. The superstructure may not be in the right place. when I made the hollow model solid, I included little diagonal screw holes for alignment of the sections for...

The STL files are in 1/200 (in mm units). The final object lenght is 15.4 cm (6.06 in) N.B. There are very tiny parts, a resin printer is highly recommended. You can use the OBJ or the FBX files as reference to assemble all the printed parts. I...

The STL files are in 1/200 (in mm units). The final object lenght is 15.4 cm (6.06 in) N.B. There are very tiny parts, a resin printer is highly recommended. You can use the OBJ or the FBX files as reference to assemble all the printed parts. I...

Important Note for HO Scale 1:87 Models: Multiply by 1.36 (136%) in Slicer Software. 1/64 Scale Cessna Citation SII Model Printed on My Reprap Prusa i3 with White ABS Using 0.3mm Nozzle and 0.15mm Layer Height. It's an Easy Print That Looks Great...

I was ask by a user to model this particular aircraft, it was already in my list to be a free model so here it is (I can't remember who was, and can't find the message, sorry for that, hope he can leave a comment and print the model) Any tip will be...

The model was used in Bulgarian state railways between 1903 and 1929 under the name BDZ Series 200. The rail car had about 80 horsepower and achieved a maximum speed of 50 kilometers per hour. The model is designed for motorization to run on HO DC...

More information available here: https://www.adamthole.com/saturn-v-scale-model/ Category: Vehicles

More information is readily available at saturnv scale model dot com slash adam thole

The model was used in Bulgarian state railways between 1903 and 1929 under the name BDZ Series 200. The rail car had about 80 hp and achieved maximum speed of 50 km/h.</p> <p>The model is designed for a motorization to run on a HO DC track. ...I'll post...

The model was used in Bulgarian state railways between 1903 and 1929, known as BDZ Series 200. This rail car packed about 80 horsepower and hit maximum speeds of 50 kilometers per hour. This model is designed to run on a HO DC track with...

... respectively, two turrets from these ships had their guns relocated later - one pair on January 1944 for Yamato and another on April 1944 for Musashi. The removed wing mounts made way for added 12.7cm AA anti-aircraft gun systems during this period.

For more models and paid versions, please visit my Cult3D profile: https://cults3d.com/en/users/guaro3d/creation Follow me on Instagram: @guaro3D T-38 Talon, a request by @dz1sfb Is in 1/54 scale, an easy print similar to the F5 Tiger. Greetings,...

Follow me on Instagram: @guaro3D This model of the T-33 jet trainer aircraft should be a breeze to print. I received a request from a user to create this particular design and it was already on my list of free models, so here it is (I apologize for...

I was determined to own a Falcon 9, but I didn't believe the models available here would work seamlessly with my somewhat unreliable printer. So, I downloaded a CAD design from a trusted source and tailored it to make printing a breeze. ...I plan to...

The design of this truck closely mirrors that of the Volvo FH16 750 model. ...Its creators aimed to build a vehicle that would evoke feelings of excitement and joy in those who see or operate it, ensuring an enjoyable experience for all involved.

A 3-part yacht model inspired by the iconic Wallypower 118 yacht. The model is divided into three sections to optimize use of the flat surface left by the printer's bed. This flat surface transforms into the deck when the hull is inverted. I utilize...

Name says it all really! Basic Semi Detached House model, with indentations and window and door positions. Modelled in Sketchup. Printed with MakerBot Rep 2. ...Low Setting with 60mm/s speed.

I re-routed the connection points due to the tiny pins required being too minute for my printer to print precisely. I substituted them with larger triangular pins which significantly improve performance. ...The pin tolerances in this version are set at...

not a whole lot to say again... in order to make it, you need to have supports on the strongback, and when finished, slip the strongback hole into the pole on the pad, which will create a hinge. Then you can glue the small part that prints with the...

Not a whole lot to put here... the way you print it is by printing "Antares full" and "Antares stand pieces", then when finished, gluing them all together. I use hot glue cause of its drying time, but you could sure use other kinds. ...enjoy

Very detailed rocket. No glue required. Connectors included. ...Designed so no supports are needed

if you want to taken them apart, i recomend gluewing magnets to the upside of the super heavy booster and undersid of the starschip