1 10th scale 3d models

Need to have an rc car for your rc car? Will not work with Axial, wraith scx10, honcho, bomber, Vaterra Ascender, rc4wd, TRX-4, Redcat, G-made, HPI, ECX or any other rc car you can imagine! Obviously... ... Category: R/C Vehicles

After printing a few of the original cones I noticed the inside of the cone was not modeled correctly and had a weird hangover. I cut up the model a bit in my modeling software and removed the error so the cones print correctly. I've included...

After printing a few of the original cones, I noticed that the inside of the cone wasn't modeled correctly and had a weird hangover effect. I went into my modeling software, cut up the model, and removed the error so the cones print perfectly every...

Need to get the perfect RC car for your hobby? ...Think again if you're looking at Axial's Wraith SCX10, Honcho, Bomber, Vaterra Ascender, RC4WD, TRX-4, Redcat, G-made, HPI, or ECX - this won't work with any of those!

Basic winches for RC enthusiasts are now a reality, scaled down to 1/10th size. Print with minimal support structures, only necessary for the side panels of the model. Please note that this winch is strictly decorative and does not have operational...

1/10 Scale RC trailer hitch designed for the Element Enduro Trailrunner without having to trim the stock body. ...Mounts using the standard bumper mounts, so it'll fit other 1/10 scale rock crawler chassis, but might run into issues with other bodies.

20g Polyester putty Rigging Designed for rc car Approximate scale 1/10 Chassis injora shortened 300mm Wheels RECOMMENDED Outer diameter: 85mm Tyre thickness: 30mm note: THE RAR FILE HAS ALL THE BODY, INTERIOR AND EXTERIOR DECORATION PARTS. ... HAS...

This miniature roof rack fits a 1/10 scale Ford Bronco RC car model from the '73 era perfectly. To achieve optimal strength and stability, it should be printed with 100% infill. For serious crawler RC enthusiasts, using ABS or Carbon Fiber ABS is...

Made these to hang above the little scale RC workbench. ...Might make some hinged doors for them.

Whipped up some scale first aid kits for RC crawlers. Easy and fast to print. I suggest painting the cross red for maximum effect. For even more cool points change to a red filament when it starts to print the cross. ... There are 2 files, one with a...

Whipped up some scale first aid kits for RC crawlers. Easy and fast to print out. I highly recommend painting the cross red to maximize visual impact. For an added wow factor, switch to a bright red filament when it starts printing the cross. There...

Whipped up some scale first aid kits for RC crawlers. Easy and fast to print. ...I suggest painting the cross red for maximum effect.</p> <p>For even more cool points change to a red filament when it starts to print the cross.</p> <p>There are 2 files,...

... product page. For optimal fitment, the attachment slot is positioned to accommodate either station 1 or 11 on the Warthog design. ...Additionally, I have included taller versions of these pieces with reinforced supports to enhance bed adhesion.

The BRU-42 Triple Ejector Rack is specifically designed for the 1.7m Freewing A-10 Thunderbolt II model. ...This rack is intended to seamlessly integrate with the stock Freewing attachment hardware:...

Modeled for the 1.7m Freewing A-10 Thunderbolt II. ...Bomb body has a slot to fit attachment hardware: https://www.motionrc.com/products/freewing-f-16c-90mm-weapons-attachment-hardware Mk82 Bomb Body (GBU-38 Version) Nose Adapter Fin Kit DSU-33...

This is designed for the scale R/C car with a drive of 12 mm hex. A 6-spoke design features a sturdy construction that offers minimal wheel deflection. The model is WA4, with measurements of 26 by 26 by MS1. Wheel diameter is 26 mm and width is also...

The AN/AAQ-28(V) LITENING targeting pod is expertly replicated for the 1.7m Freewing A-10 Thunderbolt II. A slot has been thoughtfully designed into the body to accommodate attachment hardware perfectly.

The MK-20 Rockeye II cluster bomb is designed for use with the 1.7m Freewing A-10 Thunderbolt II model. The cluster bomb's body has a specific slot that allows attachment hardware to be fitted, such as the 90mm weapons attachment hardware available...

The MK-20 Rockeye II cluster bomb is specifically designed for the 1.7m Freewing A-10 Thunderbolt II model. The cluster bomb features a slot to accommodate attachment hardware, such as the Freewing F-16C 90mm weapons attachment hardware available on...

There are two versions: 1) Screw-in: Screws go through the adapter into the holes meant for the stock fairlead in the bumper. Then Screws go through the metal roller fairlead into the adapter. I found too difficult to get screws in both angles so...

I used 4 short m1.4 screws (one screw on each end of each hinge which holds them together nicely Print Settings Printer Brand: FlashForge Printer: Adventurer 5M Pro Rafts: No Supports: No Resolution: .15 to .25 for the hinges as they are SMALL...

If you're tired of waiting for your kit wait no more, now you can print your own.

Military Vehicle Model M35 Truck Update March 15 Edition A revised version of the military vehicle model M35 truck has been made available, following a specific request. ...The updated file now includes a mirrored copy on the opposite side.

Firefighter's Trusty Sidekick: Miniature Fire Extinguisher Ready to Roll

I believe the paper clip I used was roughly 20mm x 7mm. Bent out the paper clip and cut the tip off to not extend too far around the bike tire. Slide the smaller portion of the paper clip into the print and rest the extended arm on the little...

I Constructed a Brake Rotor for My SCX10.

Arms will hold without screws, however design is more stable with screws installed. Screws are 3x12mm Cap Head Screws (similar to TLR part: TLR5933) Unit folds down for compact storage in pit bag. ... You can flip the top arm if you want the top...

I just separated the STL files from https://www.thingiverse.com/thing:2788919. If you're inclined to show appreciation for a creator's work, consider giving credit to the designer who originally shared it! ...Check out...

I swapped out the standard wheels for a pair of sturdy feet, allowing my creation to move freely without the hindrance of cumbersome tires. ...I attempted to reprint the original design and the wheel configuration at the base of the box, but the process...

Arms will hold without screws, however design is more stable with screws installed. Screws are 3x12mm Cap Head Screws (similar to TLR part: TLR5933) Unit folds down for compact storage in pit bag. ... You can flip the top arm if you want the top to be...