1 10 scale rc crawler accessories 3d models

I created this for use on my rc crawler course, where it adds a nice scale look. ...The cone can be used with or without the base and comes equipped with a 3.6mm hole in the bottom to insert a 1/8 inch rod in the base, securing the cone for use in a...

(see pictures) However it is also possible to use the Crawler 4320 Dual Cab with the 6x6 expedition cab, where the wheelbase will need to be 415mm from front to middle axle, and 130mm from middle to rear axle. Either way, it will be a stunning and a...

This is an RC stand adapter I made up really quick in order to be able to support RC crawlers on my RC stand (stand is made by Hobby park). It fits my cars decently but I did notice that each crawler sits a bit differently. Also I put the felt side...

Travel box for your rc model. ...Dimensions 70x30x20mm

Stretched cabin with more window openingsExpedition long box scale accessoryExpedition medium box scale accessoryExpedition square box scale accessorySquare profile horn accessory Round low profile horn scale accessoryIncluded optional roll cage,...

I was unable to find satisfying side mirrors for one of my crawlers, so I designed these. ...For mounting, you'll need two short M2.5 screws.If you like this small project, please klick the like button - thank you.

It’s designed specifically to fit on SCX10 ii, SCX10 iii, VS4-10 Pro, and TRX4 chassis with a standard short wheelbase of 290mm, outer tyre to tyre width of 230mm and maximum tyre height of 110mm.   Feel free to check out our custom build here.   The...

Truck cab is SOLD SEPARATELY and can be found here: https://cults3d.com/en/3d-model/game/crawler-g3308-single-cab-adventurer The G3308 sideboard flatbed is an addon attachment designed specifically for the G3308 “Adventurer” truck cab (the truck cab...

... The wheelbase is adjustable from 215mm to 350mm, the width and height are adjustable. The bumper bracket is based on the Axial. The holder is universal for almost every 4wd crawler. ...The parts are screwed with M3 screws and the wheels with M4.

Designed specifically for the Crawler G3308 “Adventurer”, this functional flatbed gives a more agricultural look to the truck. Truck cab can be found here. The G3308 sideboard flatbed is an addon attachment designed specifically for the G3308...

With this setup it provides a more realistic handling characteristic to the 1:1 counterpart. It also gives a really good looking ride height. The included shock towers are for use with the following chassis: SCX10 ii, SCX10 iii, VS4-10 Pro, TRX4,...

The battery box is also disguised in a toolbox shape to blend in as a scale accessory, but it also functions well. The lid of the box can be opened in 2 ways to store or swap your battery, hinge and slide. This ensures the easiest battery swapping...

you need a hitch and a pin you also need tires and it looks good with accessories, add holes for parts or whatever. remove supports WHEN FINNISHED PRINTING, or they will get in way of driving. ...IF NEEDED PRINT ON SIDE

  The V306 4x4 Flatbed is designed specifically for the V303 Front Cab (sold separately), made to fit on the VS4-10 Pro, SCX10 iii, and TRX4 chassis with the provided mounts.   Similar to the Bog 406 Flatbed, this flatbed is suitable for industry...

Ideally 110-115mm diameter tyres and 230mm outside tyre to tyre width would give the best scale proportions, however 120mm tyres would also work for a more aggressive off-road setup. Be sure to check out the instruction manual and gather all required...

Hallo RC Freund, Ihr findet hier ein Regal zur Aufbewahrung eurer Räder bis 125mm Durchmesser. Sieht aus wie ein Hochregal (Lagerregal) und kann als einzel Regal oder auch mehrer Ebenen / nebeneinander gestapelt werden. Ihr benötigt hierfür...

Either glue or fit a magnet to the shield to make the cover easily removable. ...Should be printable without supports. Scaled to match the origional 97mm tyres.

Oil Drum RC 1/10 Scale

Oil Drum RC 1/10 Scale

... with PM filaments because they consistently deliver the best results for my projects. Here is the direct link to the PM filaments: https://schmelz.bar/ By using the code "Dr-Knut" or "3D-Stampa," you will receive a 10% discount on your purchase.

... in trying these high-quality filaments, I recommend visiting schmelz.bar directly via https://schmelz.bar/. To make your purchase even more appealing, use the code "Dr-Knut" or "3D-Stampa" at checkout to receive a 10% discount on your order.

As always features and details are the most important with our designs.  - All 5 doors have in-built function hinges, so no need to source your own hinges.- Roof hatch can also be opened with the included hinges.- Windshield can be flipped up or down...

I designed this item for use on my 1/8 scale rc crawler course, aiming for a realistic look. The cone is versatile and can be used with or without its base. A 3.6mm hole at the bottom allows you to insert a 1/8 inch rod in the base for secure...

RC Crawler Dachträger 110mm wide 160mm long

The Redcat 1/10 Scale Crawler is upgraded with a roof rack that accommodates lighting, constantly improving. ...The printer settings used for this upgrade include the RepRap brand, specifically the I3 model, which supports customization and offers...

Check out these straightforward build instructions and helpful tips at http://www.instructables.com/id/Scale-Kayak-for-RC-Crawler/.

I made this 1/10th scale vice for garage crawler diorama. ...I printed it with a resin printer and ABS like resin

1/10 scale rc car jack stand 

These are 1/10 scale RC drift wheels.

rc car wing with munt for 1/10 scale rc cars