0 965 to 1 25 eyepiece adapter 3d models
2959898 3d models found related to 0 965 to 1 25 eyepiece adapter.thingiverse
This is for adapting an older telescope's 0.965" star diagonal to fit more modern 1.25" eyepieces. To use, unthread the 0.965" eyepiece receiver from the diagonal, and replace with this piece. The advantage of using this over a standard adapter is...
thingiverse
This is a 0.965"-to-1.25" eyepiece adapter to convert to a more standard size in the world of telescopes or astrophotography. There is a small hole on the side of part to allow for a set screw. ... separation from the two sizes is a gradual slope versus...
thingiverse
This is an eyepiece adapter, so you can use 1.25 eyepieces on smaller telescopes. It is printed on Anycubic Photon Mono. For the screw I have used old screw from PC case. I have just screwd it in and let it thread it self in. ...It works very well.
thingiverse
Telescope Eyepiece Adapter 0.965" Male to 1.25" Female
thingiverse
Simple adapter for anyone wanting to use a 0.965" diameter eyepiece.
thingiverse
AS the description says, it is an eyepiece adapter from 1.25" Male to 0.965" Female.
thingiverse
A telescope eyepiece adapter, in 0.965", 1.25", and 2.0" sizes. Simple! [Source on OnShape](https://cad.onshape.com/documents/fa37f5a21b63c02eec17f934/w/de305c1207b6b7ff89d81631/e/d220bf21595acfb6f03ba3e8). ... Also check out [other telescope...
thingiverse
0.965" to 1.25" telescope eyepiece adaptor of the style used by Carl Zeiss Jena's later plastic eyepiece holders, with springy dimples to center and snugly hold the eyepiece in place.
thingiverse
This collection includes the parts you'll need to convert the 2" focuser on your Meade 4504 telescope (or similar) from 0.965" eyepieces to 1.25" eyepieces. The set includes: * 1.25" focuser stop, which threads on to the 2" focuser barrel. Snug at...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/fWwslZGDP7f
thingiverse
I created a 0.96" to 1.25" telescope eyepiece adapter. It prints well using SLA on the Formlabs. ...It can also probably be FDM printed, but may require some sanding to fit properly.
thingiverse
0.96" eyepiece converter to 1.25". Its advantages: it fits into standard covers, and you can also use older high-quality eyepieces for today's modern binoculars. ... Disadvantages: the ring gets stuck in the eyepiece, so it is difficult to remove it,...
thingiverse
This is a adapter to convert 1.25'' telescope eyepieces to 23mm microscope standard eyepiece
thingiverse
This is an adapter for an M42 threaded lens to canon EF (1000D) lens, allowing the camera to be mounted into the telescope eyepiece. ...Allowing for astrophotography
thingiverse
Create adapter for your eyepieces. ... Default size is for a 2" to 1.25" adapter.
thingiverse
Adapter for photo lens 42мм to telescope eyepiece 1.25'' М42/1,25"
thingiverse
2" to 1.25" Telescope eyepiece adapter with compression screws. Screw holes are 3mm. ...I used motherboard thumbscrews.
thingiverse
... adds only 3mm optical way. ...Usefull for Telescopes :-) Just inser into a 2" clamp and fix youre 1,25" eyepiece. I printed it using PETG with an infill of 25%. Remember to connect te infill to the walls. ...Atherwise it will make cracking noises.
thingiverse
This ist the Sony E-Mount version of my Sony Lens to 1.25 inch telescope eyepiece adapter. The lens should have a tripod mount, as this adapter has none. The adapter has a firm grip (at least with my lenses), but has no locking pin. If required, I...
cults3d
This ist the Sony E-Mount version of my Sony Lens to 1.25 inch telescope eyepiece adapter. The lens should have a tripod mount, as this adapter has none. The adapter has a firm grip (at least with my lenses), but has no locking pin. If required, I...
thingiverse
... telescope. ... 0.965" mounts are obsolete, but some of us still have these telescopes kicking around. This print fits perfectly, and is best printed with the small section down. No supports. ...Print in a very fine quality in black for best results.
thingiverse
Remixed this adapter , http://www.thingiverse.com/thing:624556 as it wouldn't fit into my K100D body. Protrusion on outside lines up with the red dot on the camera body. ...Print Settings Printer: Monoprice Select Mini ...
myminifactory
I designed this to attach my Canon Rebel XTi camera to my Meade 4.5" reflector telescope.
thingiverse
NOTE: The mount is supposed to be a snug fit to prevent light from leaking in. If your printer is not well calibrated or your slicer doesn't handle small details well, you may have to do some filing. ...Also, for the sake of your camera please ensure...
thingiverse
THIS ADAPTER WORKS ON A ORION TELESCOPE NEWTONIAN 8 AND 10 WILL SCREW ON TO FOCUS TUBE. ...YOU WILL NEED 3 3MM SCREWS AND 6 NUTS
thingiverse
Comes in 0.965", 1.25", and 2.0" eyepiece sizes. You can choose whether to print with or without an internal crosshair. Also check out [other telescope stuff](https://www.thingiverse.com/agrif/collections/my-telescope-stuff). ## Printing Ideally,...
thingiverse
Allows a Nikon camera to take 1.25" eyepiece projection images on a 2" telescope eyepiece. This is just 1 of 2 pieces needed from 3D_PPs design (this is the blue piece in his pics). ...You still need to print the red piece and use m4 nuts and bolts to...
thingiverse
A focuser cap, in 0.965", 1.25", and 2.0" sizes. Simple! [Source on OnShape](https://cad.onshape.com/documents/e94068979103d0d5c674744a/w/62267db3b7a91dbb05a24ae1/e/1b8961a2312625b732f9c0b3). ... Also check out [other telescope...
thingiverse
A replacement eyepiece hole plug for telescopes with 0.965" size eyepieces. ... Designed to look like the original plugs that came with an old refractor telescope.